Best sellers

Number of hours:. Bulb load: 400 W Max. Fluorescent lamp load (parallel compensated): 400 VA stairlight time switch with switch-off warning and pushbutton continuous light can be switched on. Stand-by-loss only 0.7 Watt. With ESL optimization and multifunction. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. In addition, with galvanically separated universal control voltage. Automatic detection of the circuit type. Glow lamp current up to 50ma, depending on the ignition voltage of the glow lamps. Precise time setting 1 to 30 minutes with minute scale. Permanent light switch with the large rotary switch. After a power failure in the function setting

Current surge switches, electronic for mounting on support rail DIN-EN 60715 TH35 potential-free 16A/250V AC, incandescent lamps 200W No stand-by loss, maximum current as a sum over both contacts 20A at 230V, connection terminal occupancy is identical with current surge switches S12 current surge switches, stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. The simultaneous use of two potentials at the tax inputs is not permissible. Very low switching noise. No constant power supply required, therefore no stand-by loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. The connection terminal occupancy is identical to the electromechanical current surge switch. Width in division units: 1 Number of locks: 1 Rated switching current: 16 A Control voltage type 1: AC/DC Installation depth: 58 mm Function: electronic switch Mounting type: DIN rail Frequency of control voltage 1: 50 - 50 Hz Voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Switching current (cos phi = 0.6): 4 A manual operation possible: No

PVC Verdrahtungsleitung Verwendung: In trockenen Räumen, in Betriebsmitteln, Schalt- und Verteilungsanlagen und als Potentialausgleichsleitung in Rohr auf und unter Putz sowie bei geschützter Verlegung in und an Leuchten. Für innere Verdrahtung von Geräten mit einer Nennspannung bis 1000 V Wechselstrom und mit einer Nennspannung bis 750 V Gleichstrom gegen Erde. Nicht zulässig für unmittelbare Verlegung in Putz.

PVC Aderleitung Verwendung: In trockenen Räumen, in Schalt- und Verteileranlagen zur Verlegung im Rohr auf und unter Putz sowie ohne Rohr auf geeigneten Isolierkörpern

Clamp for connecting or connecting wires, wires and cables with permanently secure contact. Hardened steel for mechanical forces and high-quality copper with tin coating ensure the best conductivity.

Verbindungsdose nach DIN VDE 0606, Aufputz, 7 Einführungen, 1 Bodeneinführung, zentraler Deckelschnellverschluss, mit Schutzart IP30, bis 2,5², mit Schutzgrad IK07, Schutzklasse II, VDE geprüft, 78 x 78 x 27, weiß, ohne Klemmen, für VDE-zugel. Einzelklemm

Raumtemperaturregler, 5 - 30°C, mit Schalter für Heizung EIN/AUS, Wandgehäuse 74 x 74 x 28 mm, Farbe reinweiß, Öffner 10 A/230 V~.

Clamp for fastening gratings on wall or handle booms, inclusive flat round screw FRS M6 x 20 with combination nut.

The V50 lightning current combination conductor made of halogen-free plastic is suitable for lightning protection potential compensation according to VDE 0185-305 (IEC 62305). A dynamic separation device and optical status display characterize the modularly pluggable arresters. The NPE variant is additionally equipped with a highly loadable spark gap between zero and protective conductors. The CombiController is particularly suitable for lightning protection potential compensation for buildings of the flash protection class III and IV. The flash current-abableite power is 12.5 kA (10/350) per pole and up to 50 kA (10/350) total. The vibration-proof latching and the voltage and type coding ensure safety and avoid confusion between upper and lower parts. The wedge-shaped design of the contacts allows simple insertion and even simpler removal of the upper parts. Additional technical product information can be obtained quickly and easily via the QR code applied to the power shield.

Compact 4-wire KNX/EIB connector with PUSH WIRE®- connection
Restricted ladder directly insertable
4-wire connection – no interruption of the KNX/EIB bus connection for device exchange

Serial LED aggregate with N-terminal module inserts blackSerial LED aggregate with N-terminals. ForWippen Schalter series, with durableLED technology. For control circuit perSeries, with screw clamp.Color: blackTechnical version: 230 V~, each 0.9 mA

KVFC 01
Antennen-Steckdose, Kabelverbinder, geeignet für F-Stecker.