List of products by brand Protec

AP-Klingel Electromechanical Blade. Steel sound shell (Ø 48 mm). Plastic housing for plaster mounting. Sound pressure level: approx. 80 db. Color: white. Protection type: IP20 Rated voltage: 8 W Power consumption: 5.4 VA

Temperature resistant up to 80°C. Length: 10 m. PMLV12, PMLV17, PMLV25: thickness 0.75 galvanized. PMLKU14, PMLKU19, PMLKU27: Thickness: 3.00 mm plastic coated, halogen-free. Hole distances: PMLV12: 9 mm, PMLV17: 12 mm, PMLV25: 14 mm, PMLKU14: 12 mm, PMLKU19 and PMLKU27: 15 mm Width: 12 mm Break load: 1700 N Hole-Ø: 5.1 mm

Daily timer analog. 24 h program. Channels: 1. Contact type: Wechsler. TLE: 3. Power loss: 0.85 W. Accuracy of gear: grid-synchronous. Operating voltage: 230 W AC. Operating frequency: 50 Hz. Hand operation. Protection: IP30. Mounting type: DIN rail. Ohmsch cos phi = 1: 3680 W, Inductive cos phi = 0.6: 2760 W. Incandescent lamps: 1000 W. LL series-compensated: 1400 VA. LL-parallel-compensated (

Diaphragm sleeve 2 Components Polypropylene / thermoplastic elastomer, dustproof, for use with mating nut or in existing thread, silicone-free, plug-in length: 9.5 mm, glow wire test: 750° nominal size: M 16 cable-Ø: 1 - 9 mm protection type (IP): IP66 Material: plastic Halogen-free: Yes Colour: light grey

Diaphragm sleeve 2 Components Polypropylene / thermoplastic elastomer, dustproof, for use with mating nut or in existing thread, silicone-free, plug-in length: 9.5 mm, glow wire test: 750° nominal size: M 20 cable-Ø: 1 - 13 mm protection type (IP): IP66 Material: plastic Halogen-free: Yes Colour: light grey

Diaphragm sleeve 2 Components Design of polypropylene / thermoplastic elastomer, dustproof, for use with mating nut or in existing thread, silicone-free, plug-in length: 9.5 mm, incandescent wire testing: 750° nominal size: M 25 cable-Ø: 1 - 18 mm protection type (IP): IP66 Material: plastic Halogen-free: Yes Thread length: 9.5 mm Thread type: metric Colour: light grey

Material: polyamide, screw-in nail with flat head, for minor fastenings in construction, metal, sanitary and electrical areas, for fastening light loads, such as angles, plates, sheets, cable channels and any components for non-slower assembly, Removable by drive in the screw head, areas of use: concrete, solid brick, lime sandstone, pore concrete, high hole brick, limestone temperature. Screw nail included Length: 30 mm Hole diameter: 5 mm

Conductor terminals for mounting on DIN rails, e.g. for small installation distributors and counters acc. WDE 0603 Clamping points: 7 or 12. Clamp: brass, cross section 6 mm x 9 mm. Screws: M5, steel, galvanized/passivated (Cr-VI-free). Housing: polyamide, impact resistant, flameproof. Corners rounded. Line connection: 1 ... 16 mm2 rigid / 1 ... 10 mm2 fine-wired with wire end sleeve (round pressing or square pressing, trapezoidal pressing up to 6 mm2) screw connection, recommended. Applying torque 1.2 Nm.- Standards / Requirements: Connecting material for low voltage circuits for household and similar purposes WDE 0613, EN 60998. Mounting: On DIN support rail according to EN 50022 / EN 60715. Nominal current: 63 A. Insulation voltages: 690 W (distributor and control cabinet inlet, degree of contamination 2). 500 W pollution level 3) Uimp = 6 kw. Touch protection: IP00 Type additive Ä-F2 –: IP20, fingerproof. Screw terminal. Combi-cross slot Z2 (positive).

Conductor terminals for mounting on DIN rails, e.g. for small installation distributors and counters acc. WDE 0603 Clamping points: 7 or 12. Clamp: brass, cross section 6 mm x 9 mm. Screws: M5, steel, galvanized/passivated (Cr-VI-free). Housing: polyamide, impact resistant, flameproof. Corners rounded. Line connection: 1 ... 16 mm2 rigid / 1 ... 10 mm2 fine-wired with wire end sleeve (round pressing or square pressing, trapezoidal pressing up to 6 mm2) screw connection, recommended. Applying torque 1.2 Nm.- Standards / Requirements: Connecting material for low voltage circuits for household and similar purposes WDE 0613, EN 60998. Mounting: On DIN support rail according to EN 50022 / EN 60715. Nominal current: 63 A. Insulation voltages: 690 W (distributor and control cabinet inlet, degree of contamination 2). 500 W pollution level 3) Uimp = 6 kw. Touch protection: IP00 Type additive Ä-F2 –: IP20, fingerproof. Screw terminal. Combi-cross slot Z2 (positive).

Zero,- protective conductor and diverter terminal conductor terminals for mounting on DIN support rails, e.g. for installation small distributors and counters acc. WDE 0603. Clamping points: 14 plug connections + 1 screw connection possible to mount behind the clamp cover. Corners rounded. Cable connection: plug connection 12 x 1 ... 2.5 mm2 rigid/multi-reversal or. 0.75 ... 1.5 mm2 with wire end sleeve 2 x 1 ... 4 mm2 rigid/several, plug connection 1 ... 2.5 mm2 with wire end sleeve screw connection (feed line): 1 x 1.5 ... 25 mm2 rigid/several. 1 ... 16 mm2 with wire end sleeve. standards / regulations: connecting material - electrical copper conductors; Safety requirements for screw terminals and screwless clamping points. WDE 0609, Part 1 / EM 60999-1 Connecting material for low voltage circuits for household and similar purposes WDE EN 60998-1; WDE 0613-1. Mounting: On DIN support rail according to EN 50022 / EN 60715 rated current: 80 A (feed line). Insulation voltages: 500 V (degree of contamination 2, overvoltage category III). Contact protection: BGW A2 / WBG4, fingerproof

Nail clamps impact resistant, highly elastic polyethylene, halogen-free and silicone-free, special-hardened steel nail, continuous nail guide, impact stop prevents too wide impact of the nail, wide web for firm grip on any substrate, UV-resistant, nail supplied cable-Ø: 10 - 14 mm nail length: 35 mm

Nail clamps impact resistant, highly elastic polyethylene, halogen-free and silicone-free, special-hardened steel nail, continuous nail guide, impact stop prevents too wide impact of the nail, wide web for firm grip on any substrate, UV-resistant, nail supplied cable-Ø: 7 - 11 mm nail length: 25 mm