List of products by brand Protec

SCHUKO® 2-pin + PE, 16 A Color: white SCHUKO angle connector made of thermoplastic, 2 polig + earth, 16A 250W, according to DIN 49440/441, color white

NH00 Locking inserts with metal handle tabs NH00 Low-voltage protection, according to DIN WDE 0636 part 2, nominal voltage: 500W AC / 220W DC, width: up to 100A 20 mm / from 125A 30 mm, NH000 to 100A / NH00 from 125A, voltage-carrying handle tab, operating class (gL)-gG full-range safety inserts (for cable and cable protection) for general applications

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 76x76x51 mm For cable Ø: 3-14 mm Max. Conductor cross-section: 2.5 mm2

Temperature resistant up to 80°C. Length: 10 m. PMLV12, PMLV17, PMLV25: thickness 0.75 galvanized. PMLKU14, PMLKU19, PMLKU27: Thickness: 3.00 mm plastic coated, halogen-free. Hole distances: PMLV12: 9 mm, PMLV17: 12 mm, PMLV25: 14 mm, PMLKU14: 12 mm, PMLKU19 and PMLKU27: 15 mm Width: 12 mm Break load: 1700 N Hole-Ø: 5.1 mm

Device connection box for the wall connection of electric stoves and similar applications (transition of rigid wiring to flexible wiring). Snap lid. Clamps with color coding corresponding to valid vein colors. WDE 0606-1 / EN 60670-1, 2005-10 and WDE 0606-22 / EN 60670-22, 2007-07. Cross section: 5 x 2.5 mm2. PHAD: Double cable outlet. Line connection: feed line: max. 4 mm2 rigid/multiplier; outlet: max. 2,5 mm2 with a core end sleeve; Screw connection (jack clamp). Number of clamping points: 5. Mounting: In standard switch box ø 60 mm, PHAD alternatiw screw fastening on plaster. Touch protection: fingerproof IP20. Safety: corners rounded assembly type: undercut

C-profile rail C-profile rails for professional fastening of pipes and pipes. Profile: C-profile. Slot width: 17 mm. Type of hole: back holed. With three holes. Hole: 6,5x12 by mm; 8,7x20 of mm; 10,5x15 mm. Tested for laying fire protection cables according to DIN 4102-12 : 1998-11, with expert opinion (see www.protecclass.de). Material: steel. Surface: galvanized, transparent passivated Length: 500 mm Width: 35 mm Height: 18 mm Material thickness: 1.25 mm

Conductor terminals for mounting on DIN rails, e.g. for small installation distributors and counters acc. WDE 0603 Clamping points: 7 or 12. Clamp: brass, cross section 6 mm x 9 mm. Screws: M5, steel, galvanized/passivated (Cr-VI-free). Housing: polyamide, impact resistant, flameproof. Corners rounded. Line connection: 1 ... 16 mm2 rigid / 1 ... 10 mm2 fine-wired with wire end sleeve (round pressing or square pressing, trapezoidal pressing up to 6 mm2) screw connection, recommended. Applying torque 1.2 Nm.- Standards / Requirements: Connecting material for low voltage circuits for household and similar purposes WDE 0613, EN 60998. Mounting: On DIN support rail according to EN 50022 / EN 60715. Nominal current: 63 A. Insulation voltages: 690 W (distributor and control cabinet inlet, degree of contamination 2). 500 W pollution level 3) Uimp = 6 kw. Touch protection: IP00 Type additive Ä-F2 –: IP20, fingerproof. Screw terminal. Combi-cross slot Z2 (positive).

Heat resistant up to 105°C, halogen-free nominal cross-section: 10.0 mm2 wire cross-section: 2 x 10 mm2 sleeve length: 14 mm Colour: red

Suitable for cable fittings PKWM thread size metric/PG: 32 thread type: metric material quality: polyamide halogen-free: Yes fiberglass reinforcement: Yes incline: 1.5 RAL: 7035 Key width: 40 mm

Up to 100 A tension-free handle tabs made of metal, from 125 A tension-free handle tabs made of metal with center detector, according to DIN WDE 0636 part 2, DIN 43620 and DIN EN/IEC 60269-1 and DIN EN/IEC 60269-2, nominal voltage: AC 500 W, DC 220 W, selectivity inserts factor: 1.6, operating class (gL)-gG

2 Components Humidity Drainage Box High ease of assembly and easy handling, three penetration membranes on all four sides, rear membrane introduction for lines up to 5 x 2.5 mm2, loss-proof lid, fastening strap for cable tie assembly. Protection: IP 54. Color: grey. Windproof, halogen-free. 12 introductions from behind. Length: 85 mm Width: 85 mm Depth: 45 mm Material: plastic Type of housing passage: sealing membrane

Tool box With a large and two small compartments,Devices (Löcher) for screwdrivers, impact resistant, resistant to fats, oils, alkalis and resins, Dimensions: approx. 38 x 25 x 14,5 cm Colour: blue Material: plastic