List of products by brand Eltako

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours and the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1A. Time range from/to: 40 - 0.1 function: clock generator with pulse starting number of switches: 1 switching power incandescent lamps: 2000 W width in division units: 1 supply voltage range: 8 - 230 W switching power fluorescent lamps inductor: 1000 VA installation height: 58 mm switching power fluorescent lamps DUO: 1000 VA actuation type: analog with single function 1. Time unit: minutes/hour Mounting type: DIN rail Analog adjustable time relay. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. In the TGI12DX-UC type, a second multiplier t1 and t2 can be set separately at the same time basis. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence.

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours as well as the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sinus wave, 0.1 Watt-by-adjustable time. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. In the EAW12DX-UC type, a rotary switch can be used to set the functions of switch-on wipers (EW), switch-off wipers (AW) or switch-on and switch-off wipers (EAW). To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence. control voltage 1: 8 - 230 W control voltage type 1: AC/DC switching power fluorescent lamps parallel: 500 VA 1. Time range from/to: 40 - 0.1 Function: Switch-on/off switch relays Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductiv: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA Actuating type: analog with multifunction 1. Time unit: minutes/hour assembly type: DIN rail

LED dimming switch for installation and AP mounting Power MOSFET for LED lamps 12-36 W DC to 4 A, pulse width modulation PWM. Stand-by loss only 0.1 Watt. Minimum brightness and dimming speed adjustable, Children's room and slumber circuit Operation type: Rotary knob Halogen-free: Yes Serial dimmer: No Conveyor input: No Applicable with motion detector: No Applicable with presence detector: No Applicable with time switch/timer: No Applicable with radio button: No Applicable with IR button: No Adjustment with screw Material: Plastic Material: Thermoplastic. Stand-by loss only 0.1 Watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Dimming switches for R and LED loads up to 4A depending on the ventilation conditions. With soft-on and soft-out for lamp protection. Supply voltage 12 to 36W DC, depending on the connected LED illumination. A pulse-resistant power supply is required. Universal control voltage 8..230V UC, galvanically isolated from the supply voltage. Either directional keys can be connected to arrow up+bottom, or these connection terminals are bridged and a probe is connected as a universal probe. With universal probe: Short control commands turn on/off, permanent control changes brightness up to the maximum value. An interruption of the control changes the dimming direction. With directional sensor: turn on and dim with arrow up, turn off and dim down with arrow down. A double pulse with arrow up causes dimming up to full brightness with the set dimming speed (dimspeed). The set brightness level remains stored when switching off (memory). For a current

Current surge switches, electronic for central control work contacts and control inputs are central/local are galvanically separated, therefore local can be controlled with another phase and voltage, as central, with rotary switches various priorities can be set between the different control inputs, in this case it is also decided whether the device switches off in a defined manner after a mains failure or maintains the switch position, Glimm lamp current equal to 110W control voltage. Stand-by loss only 0.03 to 0.4 Watt. Priorities of central control can be selected. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. With additional control inputs centrally and centrally separated from the local control input for 8.230V UC. Supply voltage like the local control voltage. Very low switching noise. Glow lamp current from 110W control voltage up to 50ma in switch positions 1 to 3 and 5 to 7. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Maximum current as a sum over both contacts 20A at 230W. With control LED. Width in division units: 1 Number of locks: 1 Number of openers: 1 Rated switching current: 16 A Installation depth: 58 mm Function: electronic for central control Assembly type: DIN rail Frequency of control voltage 1: 50 - 50 Hz Frequency of control voltage 2: 50 - 50 Hz Voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Light

Universal power surge dimming switch for installation and AP mounting for 230V incandescent lamps and halogen lamps, for NV halogen lamps with inductive transformers and with electronic transformers up to 400W as well as for dimmable energy saving lamps in the setting ESL to 100W, with rotary switches the minimum brightness can be set, at the same time the duration of soft-on and soft-off switch is changed, children's room and slumber. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1 Watt. Minimum brightness or dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Universal control voltage 8..230V UC, galvanically isolated from the supply and switching voltage 230V. No minimum load required. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the upper %Lampe/dim-speed rotary switch can either set the dimming speed or the minimum brightness (fully dimmed). The dimming speed also changes the duration of soft-on and soft-off. During operation, the lower rotary switch determines whether the automatic lamp recognition should work or special comfort positions: AUTO allows the dimming of all lamp types. EC1 is a comfort site

Control dimming switch for EVG not potential-free 600VA and 1-10V control output 40mA. Stand-by-loss only 1 watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. In-line construction equipment for mounting on support rail DIN-EN 60715 TH35. Universal control voltage 8..230V UC, locally and centrally with the same potential. Supply voltage 230V galvanically separated. The latest hybrid technology combines the advantages of wear-free electronic control with high power of special relays. Switching in the zero passage for contact protection. 1-10V control dimming switch for EVG. 1-10V control output 40mA. Stand-by-loss only 1 watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. Also for controlling LED converters with passive 1-10V interface without auxiliary voltage up to 0.6mA. On top with auxiliary voltage. Locally and centrally one/off with the same potential. Supply voltage galvanically separated. The latest hybrid technology combines the advantages of wear-free electronic control with high power of special relays. Switching in the zero passage for contact protection. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and it is switched on when the supply voltage is returned. With %-Drehschalter the minimum brightness (fully dimmed) can be set. At the same time, it is determined whether the children's room circuit and the slumber circuit are active (+KI +SL). The dimming speed can be set with the dim-speed rotary switch. The load is switched on and off with a bistable relay at the output EVG. Switching power fluorescent lamps or NV halogen lamps with EVG 600VA. Due to the use of a bistable relay, there is no coil loss power and no heating heredur

Universal power surge dimming switch for installation and AP mounting for R, L and C loads up to 400 W depending on the ventilation conditions, autom. detection of load type R+L or R+C, with %-Drehschalter the minimum brightness (fully dimmed) can be set, the set brightness stage remains stored when switching off, automatic electronic overload protection and over temp shutdown, children's room and slumber circuit, switching in zero-crossing with soft-on and soft-out for lamp protection, control inputs for light scanners, etc. Light switch, without N connection, stand-by loss only 0.7 W universal dimming switch 230V without N connection. Without N connection, Power MOSFET up to 400W. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R, L and C loads up to 400W, depending on the ventilation conditions. Automatic detection of load type R+L or R+C. Energy saving lamps ESL cannot be switched with dimmers without N-connection. Control voltage 230V. Minimum load 40W. Switch in zero passage with soft-on and soft-out for lamp protection. With %-Drehschalter the minimum brightness (fully dimmed) can be set. The dimming speed can be set with the dim speed rotary switch. At the same time, the duration of soft-on and soft-off is changed. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. In the event that light switches cannot be replaced by light switches, a separate control system is

Universal dimming switch without N connection, Power MOSFET up to 200W. Stand-by-Lower only 0.5 W, with control inputs for light sensor and light switch, minimum brightness, mode of operation and dimming speed adjustable, in the event that light switch cannot be replaced by light sensor, a separate control input for light switch is present, with children's room circuit, and slumber circuit nominal voltage: 230 W Color: blue Operation type: rotary knob Halogen-free: Yes Load type: universal. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. Minimum brightness, operating mode and dimming speed adjustable. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R and C loads up to 200W, depending on the ventilation conditions. Dimmable ESL and 230V LED lamps in the operating mode phase section up to 200W or in the operating mode phase section up to 40W, depending on the ventilation conditions. In the case of dimmable 230V LED lamps, which also light slightly in the switched-off state, a basic load element GLE must be connected parallel to the lamp. L-loads (inductive loads, for example wound transformers) must not be connected. Switching in the zero passage with soft-on and soft-out for lamp protection. Control voltage, supply voltage and switching voltage 230W. Minimum load 4W. Short control commands turn on/off, permanent control changes brightness up to maximum value. An interruption of the control changes the dimming direction. Set

Energy consumption indicator for series installation The energy consumption indicator EVA12 measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories Eltako- AC counters of class B at MID (1%), the starting current is 20 mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Up to 24 hours, up to 31 days, up to 12 months and up to 24 years can be completed. The memory can be reset. Maximum current (value): 32 A Energy consumption display with display - smart metering for support rail. Stand-by loss only 0.5 Watt. The energy consumption indicator measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories. The accuracy corresponds to all Eltako- AC counters of class B at MID (1%), the starting current is 20mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Totalreset: In order to start storing the values in exact hours, a total set is recommended at a reasonable time after installation. To do this, hold the MODE and SELECT keys simultaneously for 5 seconds until RES appears in field 1. If SELECT is now briefly pressed, all memories are set to zero. After that, the program automatically returns to the normal display.

Power surge group switches for central control Processor controlled, EGS12Z2 and EGS12Z convert the commands of the sensors or the downstream sensor relays and switch two motors or one motor or the motor disconnect relay MTR12. control voltage at terminals +B1 --A2 or. A3 to A8 shall be the same potential, the following non-sections: automatic transmission, reverse deceleration, automatic transmission, duration up to Aba3 and A4 for local control with a normal double shutter switchA3 and A4 alternating shutter for static central control a5 and A6 for local control with a normal double shutter measurement A5 and A6 alternating shutter. Stand-by loss only 0.5 Watt. 1 division unit. The tube motors of shading elements and roller shutters must not be directly connected in parallel, since otherwise, over the limit switches, back tensions and finally the destruction of the motors occur. For a motor and if the control voltage and the motor voltage are 230W, however, an EGS12Z-UC is sufficient to control more than one motor with an EGS12Z-UC or if the control voltage is unequal, a MTR12-UC must be connected for each two motors. The MTR12-UC can be operated in parallel, but require free contact outputs K2/K3 of the controlling EGS12Z-UC. These are connected to the terminals K2/K3 of the MTR12-UC. 1/2 = motor 1, 3/4 = motor 2. With a rotary switch, the functions can be locked on or off and can be switched off completely. This lock applies only to the max. 2 connected motors. In this way, individual shading elements or roller shutters can be completely or partially excluded from the automatic function of an overall controller

Wide-range switching power supply for mounting on support rail DIN-EN 60715 TH35 overload and overtemperature protection by disconnecting with automatic switch-on after the fault removal (autorecovery function) wide-range switching power supply. Stand-by-loss only 0.2 Watt. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Efficiency 86%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function). Secondary voltage 1: 24 W Width: 18 mm Max. Output power: 12 W Max. Output current: 0.5 A width in division units: 1

Switching power supplies for mounting on support rail DIN-EN 60715 TH3Stand-by-loss 0.2 Watt, short-circuit-proof, with a load greater than 50% of the rated power and always with adjacent switching power supplies above 12 Watt rated power and with dimmers a 1/2 division of ventilation unit with spacers DS12 is required, input voltage 230W AC, -(20% to +10)%, efficiency 12W DC 83%, 24W DC. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Efficiency 24W DC 87%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function).