List of products by brand Eltako

Power surge switches, electronic for mounting on support rail DIN-EN 60715 TH35 potential-free 16A/250V AC, incandescent lamps 200W No stand-by loss, maximum current as a sum of both contacts 20A at 230V, connection terminal occupancy is identical with current surge switches S12 width in division units: 1 Number of switches: 1 Number of openers: 1 Rated switch current: 16DC. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Switching current (cos phi = 0.6): 4 A manual operation possible: No power surge switch UC. No standby loss. Either universal control voltage 8..230V UC at the control input +A1/-A2 or 230W with up to 5ma glow lamp current at the control input with glow lamp symbol (L)/-A2(N). The simultaneous use of two potentials at the tax inputs is not permissible. Very low switching noise. No constant power supply required, therefore no stand-by loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. The connection terminal occupancy is identical to the electromechanical current surge switch .

Current surge switches for mounting on support rails DIN-EN 60715 TH35 rated switching power 16 A / 250 W AC or. 10 A / 400 W AC with manual actuation and switching position display mechanical storage of the switching position Number of locks: 2 Number of openers: 2 Width in division units: 2 Rated switching current: 16 A Control voltage 1: 230 - W Control voltage type 1: AC Mounting depth: 55 mm Installation type: DIN rail Frequency of control voltage 1: 50 - 50 Hz Voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 2300 W Max. Lamp load: 2300 VA Max. Fluorescent lamp load (Duo circuit): 2300 VA Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Switching current (cos phi = 0.6): 10 A manual operation possible: Yes 4-pole electromechanical current surge switch with manual actuation and switching position display. Activation time: only pulse control. 12-15W. Contact distance 3mm.

Switching relay for mounting on support rails DIN-EN 60715 TH35 rated switching power 16 A/250 W AC or. 10 A/400 W AC Electromechanical switching relay with manual actuation and switching position display. Switch-on time 100%. 4W. Contact distance 3mm. Test voltage Contact/contact 2000W and test voltage control connections/contact 4000W. Number of contacts as locks: 2 Number of contacts as openers: 2 TLE: 2 Rated control voltage Us at AC 50 Hz: 230 - W Voltage type for actuation: AC

Switching relays for mounting on support rails DIN-EN 60715 TH35 Rated switching power 16 A/250 W AC or 10 A/400 W AC Number of contacts as closer: 4 Voltage type for actuation: AC TLE: 2 Rated control voltage Us at AC 50 Hz: 230 - W Electromechanical switching relay with manual actuation and switching position display. Switch-on time 100%. 4W. Contact distance 3mm. Test voltage Contact/contact 2000W and test voltage control connections/contact 4000W.

Current surge switches for mounting on support rails DIN-EN 60715 TH35 rated switching power 16 A / 250 W AC or. 10 A / 400 W AC with manual actuation and switching position display mechanical storage of the switching position Number of locks: 4 width in division units: 2 dimensioning switching current: 16 A control voltage 1: 230 - W control voltage type 1: AC installation depth: 55 mm assembly type: DIN rail frequency of control voltage 1: 50 - 50 Hz voltage type of supply voltage: AC supply voltage range: 250 - 250 W Max. Bulb load: 2300 W Max. Lamp load: 2300 VA Max. Fluorescent lamp load (Duo circuit): 2300 VA Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Switching current (cos phi = 0.6): 10 A manual operation possible: Yes 4-pole electromechanical current surge switch with manual actuation and switching position display. Activation time: only pulse control. 12-15W. Contact distance 3mm.

Steplight time switch, electronic for mounting on support rail DIN-EN 50 022, for older installations, for the control voltage 230W AC, very low switching noise, Glow lamp current 50ma, for 3-wire circuits, not switchable, without autom. Detection of the circuit type, with a relay for 2300W incandescent lamp load, continuous light switch, switch-off warning and push-button continuous light, contact circuit in the zero passage of the sine wave to the device and lamp-saving width in division units: 1 drop-back delay: 1 - 10 min Number of switches: 1 control voltage 1: 230 - W measurement switch current: 10 A control voltage type 1: AC. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA stairlight time switch with switchable switch-off warning. Stand-by-loss only 0.7 Watt. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230W. Glow lamp current up to 50ma depending on the ignition voltage of the glow lamps. Precise time setting 1 to 12 minutes with minute scale. Own continuous light switch with the large rotary switch. For 3-wire circuits with attic lighting, not switchable. Only for retrofit

Current surge switches for support rails DIN EN 50022,Nenn Switching Power 25 A/250 W AC Number of locks: 4 Rated switch current: 25 A Control voltage 1: 230 - W Control voltage type 1: AC Mounting depth: 55 mm Installation type: DIN rail Frequency of control voltage 1: 50 - 50 Hz Voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 2300 W Max. Lamp load: 3600 VA Max. Fluorescent lamp load (Duo circuit): 3600 VA Max. Fluorescent lamp load (parallel compensated): 1000 VA Max. Switching current (cos phi = 0.6): 15 A manual operation possible: Yes Electromechanical current surge switch with manual actuation and switching position display. Only pulse control. 12-15W. Contact distance 3mm.

Switching relays for day rails DIN EN 50022, rated switching power 25 A/250 W AC Installation contactor with manual actuation and switching position display. Switch-on time 100%. 4W. Contact distance 3mm. Test voltage Contact/contact 2000W and test voltage control connections/contact 4000W. Voltage type for actuation: AC Number of contacts as closer: 2 Number of contacts as opener: 2 Rated control voltage Us at AC 50 Hz: 230 - W

Switching power supplies for mounting on support rail DIN-EN 60715 TH3Stand-by-loss 0.2 Watt, short-circuit-proof, with a load greater than 50% of the rated power and always with adjacent switching power supplies above 12 Watt rated power, and with dimmers a 1/2 division of ventilation distance with the spacers DS12 is required, input voltage 230W AC, -(20% to +10)%, efficiency 12W DC 83%, 24W DC. For installation. 45mm long, 45mm wide, 33mm deep. Input voltage 230W -(20% to +10) % efficiency 81%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function). Measurement current: 0.5 A

Short circuit: Yes Mounting height: 18 mm 1. Output voltage: 24 - 24 W Voltage type of supply voltage: DC Max. Output current 1: 1 A output voltage adjustable: No Rated voltage at AC 50 Hz: 230 - 230 W Stabilized: Yes Direct mounting possible: No Electrical connection: Screw connection Output voltage controlled: Yes Power output: 12 W Suitable for series installation: Yes Support rail mounting possible: Yes Wall mounting possible: No Protection type (IP): IP20 Height: 58 mm Width: 18 mm Depth: 58 mm Power supply for 24V actuators. Nominal power 12W. Stand-by loss only 0.2 Watt. DIN-EN 60715 TH35 for mounting on support rail. 1 division unit = 18mm wide, 58mm deep. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Input voltage 230W -(20% to +10) % efficiency 86%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function). The 24W DC output of these switched-mode power supplies is at the bottom so that a fast connection to the FAE14LPR actuators for 24W DC actuators can be established with the busbars SAS-. The SNT14 is always mounted to the right next to the last actuator FAE14LPR, since no plug-in bridge is provided. Power supply for 24V actuators. Stand-by loss only 0.2 Watt. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Efficiency 86%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off

Control relays for support rails DIN EN 60715 TH35 switching position indicator by light-emitting diode, low control power requirement, low switching noise, for small currents, low self-heating, with integrated freewheeling/locking diode (A1=+, A2=′′), ER12-001-12230 W UC according to WDE 010, part 101, therefore also used as coupling relays, nominal switching power: 1250. No standby loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Low switching noise. Control indicator with light-emitting diode. Integrated freewheel/leak diode (A1 =+, A2 =−). Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. This relay is not suitable for feedback with the switching voltage of a dimming switch. The electronics have no own power supply and therefore no stand-by loss. Only when the control contact is closed is the microcontroller which switches the bistable relay in the correct direction. When the control contact is opened or a falling control voltage is switched back.

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours and the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1A. Time range from/to: 40 - 0.1 Function: Response delay Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductor: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA. Time unit: minutes/hour Mounting type: DIN rail Analog adjustable time relay. Stand-by-loss only 0.02 - 0.4 Watt. This analog-adjustable time relay is identical to the multifunction time relay, but has only one function. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence.