List of products by brand Eltako

Current relays for mounting on support rail DIN-EN 60715 TH35, potential-free 16 A /250 W AC, stand-by loss only 0.8 Watt current relay, stand-by loss only 0.8 Watt. Mounting unit for mounting on support rail (1 TE). To this end, simply connect the N conductor to the terminal (N) and L to 1 (L). This results in an additional stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. With an internal ring core current converter, the alternating current flowing via a consumer W1 is compared with the set value from 0.1A to a maximum of 32A and, when exceeded, a relay switches off a consumer W2 connected to 2 within 0.5 seconds or a consumer W3 connected to 3. Adjustment accuracy ±5%. From 25A, the relay always switches on. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. The current base A is set with the lower latching rotary switch A. TLE: 1 Number of contacts as changer: 1 Rated control voltage Us at AC 50 Hz: 230 - W

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours and the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1A. Time range from/to: 40 - 0.1 Function: Response delay Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductor: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA. Time unit: minutes/hour Mounting type: DIN rail Analog adjustable time relay. Stand-by-loss only 0.02 - 0.4 Watt. This analog-adjustable time relay is identical to the multifunction time relay, but has only one function. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence.

Bus bridge connectors for wire connections of bus and power supply bridges, series 14, 45 cm long, 4-wire strand with soldered plug-in bridges on both sides Bus system EIB/KNX: No Bus system Funkbus: Yes Bus system Powernet: No Mounting type: other number of connections: 2 Bus system LON: No Other bus systems: without bus bridge connectors for wire connections of bus bridges. 4-wire cord with soldered plugs on both sides. The BBW14 Bus Bridge Connector can connect bus parts on various support rails. In order to connect series assembly units of the series 14 with transverse wiring bus and power supply with plug-in bridges on various support rails in a switch cabinet or distributor in a space-saving manner, bus bridge connectors are plugged onto at the end of a series of devices and at the beginning of the next series of devices.

Electrical power meter Maximum power 3x80A, Stand-by-loss only 0.5 Watt per path, Row-mounting device for mounting on support rail DIN-EN 60715 TH35 in installation cabinets with protection class IP51, 4 division units = 70 mm wide, 58 mm deep, accuracy class B (1)%, with S0 interface, which measures directly measuring rotary power meter

Electricity meter Maximum current 3x80A, series mounting device for mounting on support rail DIN-EN 60715 TH35 in installation cabinets with protection class IP51, accuracy class 1 (1)%, with SO interface, 800 Imp/kWh, it can be connected 1, 2 or 3 external conductors with current consumption up to 80 A, the starting current is 2oma, the N connection must be present

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours as well as the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sinus wave, 0.1 Watt-by-adjustable time. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. In the EAW12DX-UC type, a rotary switch can be used to set the functions of switch-on wipers (EW), switch-off wipers (AW) or switch-on and switch-off wipers (EAW). To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence. control voltage 1: 8 - 230 W control voltage type 1: AC/DC switching power fluorescent lamps parallel: 500 VA 1. Time range from/to: 40 - 0.1 Function: Switch-on/off switch relays Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductiv: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA Actuating type: analog with multifunction 1. Time unit: minutes/hour assembly type: DIN rail

Power surge group switches for central control Processor controlled, EGS12Z2 and EGS12Z convert the commands of the sensors or the downstream sensor relays and switch two motors or one motor or the motor disconnect relay MTR12. control voltage at terminals +B1 --A2 or. A3 to A8 must be the same potential, the following non-sections: automatic transmission, reverse deceleration, automatic transmission, duration up, duration Aba3 and A4 for local control with a normal double shutter switchA3 and A4 alternating controller for the static central controller A5 and A6 for local control with a normal double shutter A5 and A6 alternating actuator A7 dynamic for the central controller A250. Electric shock group switches for central control for 1 motor or for motor relays. Stand-by loss only 0.05 to 0.4 Watt. This current surge group switch converts the commands of the sensor relays or of switches and pushbuttons, and switches a motor, motor separation relays MTR12-UC or DC motor relays depending on the setting of the turntables on the front side. The operating principle of this current surge group switch is that, on the one hand, on the other hand, on the other hand, on the other hand, both contacts can be controlled in a pulse-wise manner, on the other hand, on the other hand, by means of additional control inputs can be selected specifically on or off. Dynamically denotes control inputs in which a pulse of at least 20 ms is sufficient to close a contact. Static is a control input in which the contact is closed only as long as the control command is present. The names on and off apply to roller shutters, blinds and roller blinds. Number of locks: 2 Width in division units: 2 Rated switching current: 16 A Control voltage 1: 8 - 230 W

LED dimming switch for installation and AP mounting Power MOSFET for LED lamps 12-36 W DC to 4 A, pulse width modulation PWM. Stand-by loss only 0.1 Watt. Minimum brightness and dimming speed adjustable, Children's room and slumber circuit Operation type: Rotary knob Halogen-free: Yes Serial dimmer: No Conveyor input: No Applicable with motion detector: No Applicable with presence detector: No Applicable with time switch/timer: No Applicable with radio button: No Applicable with IR button: No Adjustment with screw Material: Plastic Material: Thermoplastic. Stand-by loss only 0.1 Watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Dimming switches for R and LED loads up to 4A depending on the ventilation conditions. With soft-on and soft-out for lamp protection. Supply voltage 12 to 36W DC, depending on the connected LED illumination. A pulse-resistant power supply is required. Universal control voltage 8..230V UC, galvanically isolated from the supply voltage. Either directional keys can be connected to arrow up+bottom, or these connection terminals are bridged and a probe is connected as a universal probe. With universal probe: Short control commands turn on/off, permanent control changes brightness up to the maximum value. An interruption of the control changes the dimming direction. With directional sensor: turn on and dim with arrow up, turn off and dim down with arrow down. A double pulse with arrow up causes dimming up to full brightness with the set dimming speed (dimspeed). The set brightness level remains stored when switching off (memory). For a current

Switching relay for mounting on support rails DIN-EN60715 TH35 No heat losses due to internal bistable relay,DX=Eltako-Duplex technology, switch in the zero crossing of the sine wave of a 230V switching voltage, low switching noise, control indicator with light-emitting diode, integrated freewheel/lowering diode (A1 =+, A2 =−) switching relays. No standby loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. To this end, simply connect the N conductor to the terminal (N) and L to 1 (L). This results in a stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. Very low switching noise. Control indicator with light-emitting diode. The connection terminal occupancy is identical to the electromechanical switching relay R12-100-. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. This relay is not suitable for feedback with the switching voltage of a dimming switch. The electronics have no own power supply and therefore no stand-by loss. Only when the control contact is closed is the microcontroller which switches the bistable relay in the correct direction. When the control contact is opened or a falling control voltage is switched back. TLE: 1 Number of contacts as closer: 1 Rated control voltage Us at AC 50 Hz: 8 - 230 V

Control relays for support rails DIN EN 60715 TH35 switching position indicator by light-emitting diode, low control power requirement, low switching noise, for small currents, low self-heating, with integrated free-wheeling/lowering diode (A1=+, A2=′′), ER12-001-12 ̊230 W UC according to WDE 010, part 101, therefore also used as coupling relay A250. No standby loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Low switching noise. Control indicator with light-emitting diode. Integrated freewheel/leak diode (A1 =+, A2 =−). Safe separation according to WDE 0106, part 101, therefore also usable as a coupling relay. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. This relay is not suitable for feedback with the switching voltage of a dimming switch. The electronics have no own power supply and therefore no stand-by loss. Only when the control contact is closed is the microcontroller which switches the bistable relay in the correct direction. When the control contact is opened or a falling control voltage is switched back. TLE: 1 Number of contacts as changer: 1 Rated control voltage Us at AC 50 Hz: 230 - 230 W

Control relays for support rails DIN EN 60715 TH35 switching position indicator by light-emitting diode, low control power requirement, low switching noise, for small currents, low self-heating, with integrated freewheeling/locking diode (A1=+, A2=′′), ER12-001-12230 W UC according to WDE 010, part 101, therefore also used as coupling relays, nominal switching power: 1250. No standby loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Low switching noise. Control indicator with light-emitting diode. Integrated freewheel/leak diode (A1 =+, A2 =−). Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. This relay is not suitable for feedback with the switching voltage of a dimming switch. The electronics have no own power supply and therefore no stand-by loss. Only when the control contact is closed is the microcontroller which switches the bistable relay in the correct direction. When the control contact is opened or a falling control voltage is switched back.

Switching relay for mounting on support rails DIN-EN60715 TH35 No heat losses due to internal bistable relay,DX=Eltako-Duplex technology, switch in the zero crossing of the sine wave of a 230V switching voltage, low switching noise, control indicator with light-emitting diode, integrated freewheel/lowering diode (A1 =+, A2 =−) switching relays. No standby loss. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Very low switching noise. Control indicator with light-emitting diode. The connection terminal occupancy is identical to the electromechanical switching relay R12-110-. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. This relay is not suitable for feedback with the switching voltage of a dimming switch. The electronics have no own power supply and therefore no stand-by loss. Only when the control contact is closed is the microcontroller which switches the bistable relay in the correct direction. When the control contact is opened or a falling control voltage is switched back. TLE: 1 Number of contacts as closers: 1 Number of contacts as openers: 1 Rated control supply voltage Us at AC 50 Hz: 8 - 230 V