Best sellers

Type of cable: 48 mm

Hammer drill SDS-Plus For working in concrete, concrete with reinforcing iron, masonry and natural stone, optimized hard metal drill tip, new hard metal geometry for superior service life and best power transmission, even less vibrations and exact guidance for more stability, easy centering, fast drilling, pleasant working, with patented KVS spinal (core-reinforced cutting spinal length)

Insulation tapes Flame retardant, ozone and abrasion resistant, ageing and weathering resistant, WDE tested 10 color set: black, white, blue, green-yellow, gray, red, yellow, brown, green, violet Length: 10 m Width: 15 mm Colour: all colors Insulation: Yes

For grounding bathtubs and hand wash basins, material screw and disc: iron, galvanized, bolt thread M6 cross section of the cable to be connected: 1.5 - 16 mm2 Material: brass Number of conductors: 1

For use in very dry interiors, for galvanized steel pipes and copper pipes, clamping band: W2A, clamping part: strip steel, support part: galvanized, chromated For pipes Ø: 1/8 to 3/8 inch cross-section of the cable to be connected: 2.5 - 10 mm2 Number of conductors: 2

Electrical power meter Maximum power 3x80A, Stand-by-loss only 0.5 Watt per path, Row-mounting device for mounting on support rail DIN-EN 60715 TH35 in installation cabinets with protection class IP51, 4 division units = 70 mm wide, 58 mm deep, accuracy class B (1)%, with S0 interface, which measures directly measuring rotary power meter

Electronic AC meter for mounting on support rail DIN-EN 60715 TH35, maximum current 32A, stand-by loss only 0.4 Watt, accuracy class B (1)%, with SO interface TLE: 1 current A: 5(32) Certified: MID calibrated tariff version of the electricity meter: tariff

Wide-range switching power supply for mounting on support rail DIN-EN 60715 TH35 overload and overtemperature protection by disconnecting with automatic switch-on after the fault removal (autorecovery function) wide-range switching power supply. Stand-by-loss only 0.2 Watt. With a load greater than 50% of the rated power and always with adjacent switching power supply components greater than 12 watts of rated power, and with dimmers, a 1/2 division unit is required on both sides with the distance pieces DS12. Efficiency 83%. Stabilized output voltage ±1%, low residual ripple. Short circuit. Overload and overtemperature protection by switching off with automatic switching on after eliminating errors (autorecovery function). Secondary voltage 1: 12 W Width: 18 mm Max. Output power: 12 W Max. Output current: 1.0 A width in division units: 1

Universal Dimming Switch Mounting type: Unterputz Color: blue Operation type: Rotary knob Halogen-free: Yes Composition: other load type: universal Serial dimmer: No Adjunct input: No Luminous accumulator: Yes Applicable with button: Yes Applicable with motion detector: No Applicable with presence detector: No Applicable with timer matt/timer: No Applicable with radio button: No. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1 Watt. Minimum brightness or dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Control voltage, supply voltage and switching voltage 230V. No minimum load required. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the upper %Lampe/dim-speed rotary switch can either set the dimming speed or the minimum brightness (fully dimmed). The dimming speed also changes the duration of soft-on and soft-off. During operation, the lower rotary switch determines whether automatic lamp detection is effective

Rated voltage: 50 %. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA stairlight time switch, without switch-off warning. Stand-by-loss only 0.7 Watt. Time setting about 0.2 to 12 minutes. Own continuous light switch with the large rotary switch. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. Without disconnection and contact circuit in the zero passage. With double connections for probe and lamp, so that it can be connected either at the top and bottom or only at the bottom.

Switching relays for mounting on support rails DIN-EN 60715 TH35 Rated switching power 16 A/250 V AC or 10 A/400 V AC Number of contacts as closer: 1 Voltage type for actuation: AC TLE: 1 Rated control voltage Us at AC 50 Hz: 230 - V Electromechanical switching relay with manual actuation and switching position display. Switch-on time 100%. Control power requirement 1.9W. Contact distance 3mm. Test voltage Contact/contact 2000V and test voltage Control connections/contact 4000V.

6 Funktionen in einer ZangeMultifunktionszange für die Elektroinstallation- zum Greifen von Flach- und Rundmaterial, Biegen, Entgraten, Kabelschneiden, Abisolieren und Crimpen von AderendhülsenGlatte Greifflächen an der Spitze für ein beschädigungsfreies Greifen von Einzeladern- profilierte Greifflächen und Brennerloch zum Greifen von Flach- und RundmaterialMarkante Außenkante an der Backe zum Bearbeiten von Unterputzdosen und Entgraten von DurchführungslöchernAbisolierlöcher für Leiter 0,75 - 1,5 mm² und 2,5 mm²Crimpnest für Aderendhülsen 0,5 - 2,5 mm²Kabelschere mit Präzisionsschneiden (induktiv gehärtet) für Cu- und Al-Kabel bis 5 x 2,5 mm² / Ø 15 mmGreifen, ohne die Zange vollständig zu öffnen (intelligenter Zuhaltemechanismus bei der Version mit Öffnungsfeder). Die Schneide bleibt geschlossen und geschütztSchlanke Bauform für gute ZugänglichkeitGeschraubtes Gelenk: präziser, spielfreier Gang der Zange