Best sellers

Suitable for cable fittings PKWM thread size metric/PG: 32 thread type: metric material quality: polyamide halogen-free: Yes fiberglass reinforcement: Yes incline: 1.5 RAL: 7035 Key width: 40 mm

Universal dimmor for mounting on support rail DIN-EN 60715 TH35, Power MOSFET up to 400 W or. 800 W, automatic lamp detection, bidirectional, stand-by loss only 0.3 Watt, minimum brightness and dimming speed adjustable, with children's room, slumber and light alarm circuit, in addition with light scene control and constant light control, no minimum load, connection to the RS485 interface universal dimming switch, power MOSFET up to 400W. Automatic lamp detection. Bidirectional. Stand-by loss only 0.3 Watt. Minimum brightness and dimming speed adjustable. With children's room, slumber and light alarm. In addition to light scene control and constant light control. Row mounting device for mounting on support rail. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230V LED lamps additionally depending on the lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Switching voltage 230V. No minimum load required. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. Connection to Eltako-RS485-Bus. Cross-wiring bus and power supply with plug-in bridge. The upper rotary switch LA/LRN is first required for learning and determines during operation whether the automatic lamp recognition should act or special comfort positions. The LED accompanies the learning process according to the user manual and displays control commands by short flashing. Width in division units: 1 Number of outputs: 1 Output power from/to: 400 - W Voltage range: 230 - V Version: Dimmaktor Power added: No Bus system EIB/KNX: No Bus system Radiobus:

Steplight time scale for mounting on support rail DIN-EN 60715 TH35, 16 A/250 V AC not potential-free, incandescent lamps up to 2300 W, ESL and LED lamps up to 200 W, control voltage 230 V and/or 8..230 V UC, switch off pre-warning and pushbutton continuous light, standby loss adjustable only 0.5 Watt. Stand-by-loss only 0.7 Watt. With ESL optimization and multifunction. The functions and times are entered according to the user manual with the MODE and SET keys and displayed digitally on the -LC display. A key lock is possible. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. The noiseless electronics do not harass the most sensitive ear, unlike many synchronous motors with mechanical transmission. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230V. In addition with galvanically separated universal control voltage 8..230V UC. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. Glow lamp current up to 50mA, depending on the ignition voltage of the glow lamps. Precise time setting 1 to 99 minutes. Own continuous light button with the protruding button SET in the functions TLZ, ESV, ES and ER. With motion detector control input BM, which converts the input signal into a control pulse in the function TLZ. Width in division units: 1 Relapse delay: 1 - 1 min Function: electronic with multifunction Assembly type: DIN rail Number of locks: 1 Control voltage 1: 230 - 23

Power monitoring relay for mounting on support rail DIN-EN 60715 TH35, for monitoring 230 W AC voltage against the zero conductor, drop delay adjustable 0.1 to 8 seconds, draw delay 0.5 s, LED display for applied voltage, with the lower rotary switch on the front side two draw-on or respectively. Relapse voltages are set: U1: 161W drop-back voltage and 185V draw voltage U2: 196W drop-back voltage and 206W draw-on voltage according to. WDE 0100 part 718 network monitoring relay with field monitoring. Stand-by-loss only 0.8 Watt. Mounting unit for mounting on support rail (1TE) For monitoring 230W AC voltage between 1 to 3 external conductors and the neutral conductor and for monitoring the rotary field (rotating in the right) in the rotary switch positions 2ph and 3ph. In the position L1/L2/L3, only the rotary field is monitored, regardless of the mains voltage. Supply voltage L1-N 180-250V/50Hz. If L1 fails, the relay will drop immediately without a relapse delay. With the lower rotary switch on the front side, two draw or. Relapse voltages are set and the number of monitored external conductors must be specified. U1: 161W falling voltage and 185V tightening voltage. U2: 196W falling voltage and 206W tightening voltage according to. WDE 0100, Part 718 (formerly: WDE 0108, Part 1). LED display for correct applied voltage. In case of incorrect polarity or a missing external conductor, the LED flashes quickly. Relapse delay RV with the upper rotary switch adjustable from 0.1 to 8 seconds. While the RV time is running, the LED flashes slowly. Suit delay 0.5s. Maximum device protection 16A. Number of contacts as changer: 1 TLE: 1

Zum Abmanteln und Abisolieren aller gängigen Rund- und Feuchtraum-Kabel von Ø 8,0 bis 13,0 mm (z. B. NYM-Kabel 3 x 1,5 mm² bis 5 x 2,5 mm²) geeignetAuch zum Einsatz in Abzweig- oder VerteilerdosenZweischaliges, aufklappbares AbisolierwerkzeugMit Öffnungsfeder und SperrklinkeBefestigungsclip zur sicheren AufbewahrungGehäuse: Kunststoff, glasfaserverstärkt

Zum Abisolieren von Koaxialkabeln (RG 58, RG 59 und RG 62)Für die Abisolierung von Außenmantel, Abschirmung und Isolation in einem ArbeitsgangMit drei eingebauten MessernDie Schnitttiefe kann für jedes Messer individuell per Sechskantschlüssel korrigiert werdenDer Messerabstand bleibt konstantGehäuse: Kunststoff, schlagfestZum Abisolieren von Koaxialkabeln (RG 58, RG 59 und RG 62)Für die Abisolierung von Außenmantel, Abschirmung und Isolation in einem ArbeitsgangMit drei eingebauten MessernDie Schnitttiefe kann für jedes Messer individuell per Sechskantschlüssel korrigiert werdenDer Messerabstand bleibt konstantWerkzeugkörper aus Kunststoff

busbar clamp 1.5mm2-50mm2, for busbars 12x5mm, for Cu conductor

Clamp with protective conductor contact for connecting or connecting wires, wires and cables with permanently secure contact. Hardened steel for mechanical forces and high-quality copper with tin coating ensure the best conductivity.

Clamp for space-saving connection or connection of wires, wires and cables with permanently secure contact. Hardened steel for mechanical forces and high-quality copper with tin coating ensure the best conductivity.

Cross connection for flexible potential distribution.

plastic clamp for isofix-EL-F, as well as all corrugated pipes, non-flammable, halogen-free, incl. clipsib safety clip at type 40/50,

The automatic safety devices of the S 200 series protect cables and cables from overload and short circuit according to DIN VDE 0100-430 and DIN VDE 0100-530. They meet the construction requirements DIN VDE 0641-11 and IEC/EN 60898-1, DIN VDE 0660-101 and IEC/EN60947-2 and UL1077. Their patented connection terminal ensures easy and secure contacting and handling by means of a printing plate. For better visibility conditions during wiring, the connection opening for lines lies above the connection opening for the phase rail. Conductor cross sections up to 35 mm2 can be connected directly to the device via the connection terminal with insulation in protection class IP20. The extensive range of accessories offers you everything you need for your installation tasks. Numerous authorisations make the S 200 fit for worldwide use. Each device is subjected to three-fold intensive tests on quality and performance before delivery.Product description on the Manufacturer page