List of products by brand Eltako

Electronic power surge switches for control voltages of 12-24 W AC and DC (UC), with interconnected transformer for galvanic separation between control and circuit. For bulbs up to 500 W and fluorescent lamps in DUO circuit up to 1000 W. Low switching noise. Electric shock switch for luminaire installation 12..24V UC. 1 lock not potential-free 10A/250V AC. Stand-by-loss only 1 watt. For installation mounting. 85mm long, 40mm wide, 28mm deep. With integrated transformer for galvanic isolation between control circuit and circuit to meet the requirements for low-voltage protection. Control voltage 12 to 24W UC, control current 10ma at 24W. Constant power supply 230W. For bulb and halogen lamp load (for lamps with max. 150W) up to 500W and fluorescent lamps with KWG in DUO circuit up to 1000VA. Fluorescent lamps with KWG parallel compensated 300VA. Temperature at the installation point between -20°C and +50°C. minimum duration/command pause 20/300ms. 4-pin pin housing for plug STOCKO MKF13264-6-0-404, 230V side 6-pin clamping bar with plug terminals, maximum conductor cross-section 2.5qmm. A Stocko plug is attached to any device. Number of locks: 1 Rated current: 10 A Control voltage 1: 12 - 24 W Control voltage type 1: AC/DC Installation depth: 28 mm Function: other assembly type: other voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 500 W Max. Lamp load (Duo circuit): 1000 VA

multifunction power surge relay for mounting on support rail DIN-EN 60715 TH35 1+1 closer, it can be selected between 18 different power surge switches or relay functions with which Eltako-Duplex technology (DX) can switch the potential-free contacts when switching 230V AC / 50Hz in the zero crossing of the sine wave, supply and control voltage 8..230V UC, rated switching power 16A/250V AC TLE: 1 number of locks: 2 number of openers: 2 width in division units: 1 Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Incandescent lamp load: 2000 W supply voltage range: 8 - 230 V control voltage 1: 8 - 230 V control voltage type 1: AC/DC frequency of control voltage 1: 50 - 50 Hz Max. Lamp load: 1000 VA Max. Switching current (cos phi = 0.6): 4 A Installation depth: 58 mm Function: partially electronic digital adjustable multi-function current surge relays. Stand-by loss only 0.03 to 0.4 Watt. To this end, simply connect the N conductor to the terminal (N) and L to 1(L) and/or 3(L). This results in an additional stand-by loss of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. The functions are entered according to the user manual with the MODE and SET keys and displayed digitally on an LC display, optionally also locked. The run-on time is constantly displayed. Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Only for the power surge switch functions: If the supply voltage fails, it is switched off in a defined manner depending on the setting or the switching position is maintained (then + in the display next to the function shortening).

Current surge relays for mounting on support rails DIN-EN 60715 TH35 16A/250V AC not potential-free, control input 230W AC and additional universal control voltage 8 to 230W UC, with rotary switches for the functions ER = switching relays, ES = current surge switches and ESW = current surge switches with reverse deceleration of 2 to 120 minutes plus switchable switch-off warning and push-off light. Relapse delay with switch-off warning and push-button continuous light can be switched on. Stand-by loss only 0.5 Watt. Contact circuit in the zero passage for protecting the contacts and lamps, in particular this extends the service life of energy-saving lamps. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Control voltage additionally with galvanically separated universal control voltage. Very low switching noise. Precise time setting of the relapse delay RV in the function ESW from 2 to 120 minutes with minute scale. With control LED. This flashes after 15 minutes with blocked probe (not in function ER). At the 230V control input Glow lamp current up to 150ma, regardless of the ignition voltage (not in function ER). In the relay functions suitable for feedback with the switching voltage of a dimming switch. If the supply voltage fails, it is switched off in a defined manner. The current surge switch automatically switches off after the set delay time has expired if the manual out command has not been given. Time range up to 120 minutes adjustable.

Current surge switch relays for mounting on support rail DIN-EN 60715 TH35 4 times power surge switch relays for central and group control, 4 independent power surge switch functions, contact 1 closer 16 A/250 V AC, 4 individual power surge switch functions with central input and output respectively. group One and Out, voltage supply, group control or local control voltage 8 ..230V UC and galvanically separated central control voltage 8..230V UC, central control commands have priority, with Eltako-Duplex technology can switch 3 of the contacts to zero passage of a connected 230V AC phase, max. Fluorescent load: 1000 VA TLE: 2 Number of locks: 4 Number of openers: 4 Width in division units: 2 Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Incandescent lamp load: 2000 W supply voltage range: 8 - 230 V control voltage 1: 8 - 230 V control voltage type 1: AC/DC frequency of control voltage 1: 50 - 50 Hz control voltage 2: 8 - 230 V control voltage type 2: AC/DC Max. Lamp load: 1000 VA Max. Switching current (cos phi = 0.6): 4 A Installation depth: 58 mm Function: semi-electronic 4-fold current surge relay, also for central and group control. With 4 independent contacts. Stand-by loss only 0.03 to 0.4 Watt. To this end, simply connect the N conductor to the terminal (N) and the outer conductors to 1(L), 3(L) or 5(L). This results in an additional stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. Local universal control voltage 8..230V UC. With additional universal voltage control inputs centrally in and out for 8.230V UC, isolated from the local control inputs galvanically. With additional group control inputs in and out for 8..230V UC. Same potential as local tax revenues.

Multifunction power surge relays can be selected with potential-free 10A/250V AC, incandescent lamps 2000W, no stand-by loss, for installation and AP installation, hybrid technology, universal control voltage 8..230V UC, no constant power supply is required, therefore no stand-by loss, due to the use of bistable relays there can also be no coil loss power in the switched-on state and no heating. 1+1 lock potential-free 10A/250V AC, light bulbs 2000W. No standby loss. For installation. 45mm long, 45mm wide, 32mm deep. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Universal control voltage 8..230V UC. No constant power supply required, therefore no stand-by loss. Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. The functions of the second rotary switch are preselected with the ES/ER rotary switch. ER selects the clamp functions. It can be selected between 10 functions: 2S = current surge switch with 2 locks. (2R) = switching relay with 2 locks. WS = power surge switch with 1 lock and 1 opener. (WR) = switching relay with 1 lock and 1 opener. SS1 = series switch 1+1 lock with switching sequence 1. (RR) = switching relay (super current relay) with 2 openers. SS2 = series switch 1+1 lock with switching sequence 2. (EW) = turn-on wiper relay with 1 lock and 1 opener, wiping time 1s. GS = groups

Current surge switches for installation and AP mounting control input 230W AC and additional universal control voltage 8 to 230W UC, with a rotary switch for the functions ER = switching relays, ES = current surge switches and ESW = current surge switches with reverse deceleration number of contacts as closers: 1 measurement control voltage Us at AC 50 Hz: 8 - 230W current surge relay 230V+UC. 1 Locker not potential-free 10A/250V AC, incandescent lamps 2000W, fallback delay with switch-off warning and pushbutton continuous light can be switched on. Stand-by loss only 0.7 Watt. For installation. 45mm long, 45mm wide, 18mm deep. Contact circuit in the zero passage for protecting the contacts and lamps, in particular this extends the service life of energy-saving lamps. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control voltage 230W, in addition with galvanically separated universal control voltage 8..230V UC. Supply and switching voltage 230W. Very low switching noise. Time setting up to 120 minutes in the function ESW. Sensors with a glow lamp current up to 50ma can be connected to the control input with a glow lamp symbol. If the supply voltage fails, it is switched off in a defined manner. If the delay time is set to a minimum in the ESW function, the relapse delay is switched off and the normal current surge switch function ES results. Switchable to the switching relay ER function. In the function ER, no glow lamp current is permissible and should only be used the control input A1-A2. In the function ER also suitable for feedback with the switching voltage of a dimming switch. When switched on

Frequency range: 50 - 50 Hz Nominal voltage: 230 W Mounting type: other central input: Yes No Number of connectable motors: 1 Switching current: 10 A separator relay 230W. 1 lock not potential-free 10A/250V AC. Stand-by loss only 0.5 Watt. For installation. 45mm long, 45mm wide, 18mm deep. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Control input with internally generated low voltage 24W DC. galvanically separated from the power supply and the working contact (PELV). Therefore, no external low-voltage power supply is required. With two L-terminals and 2 N-terminals for easy and fast installation. Power supply 230W.

Disconnection relays with window contact 1 closer not potential-free 10A/250V AC, stand-by loss only 0.5 Watt, for installation and AP installation, hybrid technology combines the advantages of wear-free electronic control with the high power of special relays, control input with internally generated low voltage 24W DC, with a disconnection transformer galvanically separated from the power supply and the working contact (PELaisV), therefore no external low voltage. 1 lock not potential-free 10A/250V AC. With window contact. Stand-by loss only 0.5 Watt. For installation. 45mm long, 45mm wide, 18mm deep. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Control input with internally generated low voltage 24W DC. galvanically separated from the power supply and the working contact (PELV). Therefore, no external low-voltage power supply is required. With two L-terminals and 2 N-terminals for easy and fast installation. Power supply 230W. The enclosed window contact consists of a reed relay with connection terminals and a magnet. The normally closed contact opens as soon as the magnet has come closer than 25mm. Connected to the terminals T1 and T2 of the separating relay ETR61NP, the power supply of a rod train is switched on as long as the window is open. The ETR61NP can be placed in the UP-Dose behind the outlet for the Dunstabzug. Installation of the window contact FK: On the housing-painted side, lever the inserts out. Connect Reedrelais and cut out housing section for the line. Both housings maximum 15mm

Universal Bus Dimming Switch for mounting on DIN-EN 60715 TH35 Power MOSFET up to 400 W, for lamps up to 400 W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230 V-LED lamps additionally depending on the lamp electronics, automatic lamp detection, minimum or maximum brightness and dimming speed adjustable, children's room and slumber circuit width. Stand-by loss only 0.3 Watt. Minimum brightness, maximum brightness and dimming speed adjustable. With children's room and slumber circuit. 1 division unit. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps and dimmable 230V LED lamps additionally depend on lamp electronics. Up to 3600W with power inputs at terminals X1 and X2. The control inputs are galvanically separated from the supply and switching voltage. Switching in the zero passage with soft-on and soft-out for lamp protection. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. From 110W control voltage glow lamp current 5ma (not at RTD). Automatic electronic overload protection and overtemperature shutdown. The functions and times are entered according to the user manual with the MODE and SET keys and displayed on the LC display. A key lock is possible.

Universal dimming switch with rotary knob, Power MOSFET up to 800W. Automatic lamp detection. Stand-by loss only 0.2 Watt. Minimum brightness and maximum brightness adjustable. DIN-EN 60715 TH35 for mounting on support rail. 2 division units = 36 mm wide, 58 mm deep. Universal dimming switch for lamps up to 800W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230V LED lamps additionally depending on the lamp electronics. Up to 3600W with power inputs LUD12 at the terminals X1 and X2. Universal control voltage 8..230V UC Mounting type: REG Color: blue Operation type: rotary knob Halogen-free: Yes Composition: other load type: universal Serial dimmer: No Conveyor input: No Light value store: Yes Applicable with button: Yes Applicable with motion detector: No Applicable with presence detector: No Applicable with timer/timer: No Applicable with radio button: No. Automatic lamp detection. Stand-by loss only 0.2 Watt. Minimum brightness and maximum brightness adjustable. DIN-EN 60715 TH35 for mounting on support rail. 2 division units = 36mm wide, 58mm deep. Universal dimming switch for lamps up to 800W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230V LED lamps additionally depending on the lamp electronics. Up to 3600W with power add-ons LUD12 at the connections X1 and X2. Universal control voltage 8..230V UC, galvanically isolated from supply and switching voltage 230W. No minimum load required. PWM control with 10-24V DC to d

Universal dimming switch for mounting on support rail DIN-EN 60715 TH35 Power MOSFET up to 400 W, for lamps up to 400 W, depending on the ventilation conditions, dimmable energy-saving lamps ESL and dimmable 230 V-LED lamps additionally depending on lamp electronics, automatic lamp detection, minimum or maximum brightness and dimming speed adjustable, children's room and slumber circuit universal dimming switch. Automatic lamp detection. Stand-by loss only 0.1 Watt. Minimum or maximum brightness and dimming speed adjustable. With children's room and slumber circuit. Universal dimming switch, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Universal control voltage, galvanically isolated from the supply and switching voltage. No minimum load required. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. From 110W control voltage glow lamp current 5ma. Automatic electronic overload protection and overtemperature shutdown. Width in division units: 1 Number of outputs: 1 Output power from/to: 400 - W Voltage range: 230 - W Power supply usable: Yes Bus system EIB/KNX: No Bus system Radio bus: No Bus system Powernet: No Bus connection included: No Bus system LON: No Other bus systems: without on-site/hand operation: Yes With LED display: Yes Parallel operation possible: No

Multifunction universal dimming switch for installation and AP mounting for R, L and C loads up to 400 W, Power MOSFET up to 400 W, dimmable energy saving lamps ESL up to 100 W, depending on the ventilation conditions, automatic lamp detection, standby loss only 0.1 W, minimum brightness adjustable, child's room and slumber circuit, standby loss only 0.1 Watt. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1Watt. Minimum brightness adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Universal control voltage 8..230V UC, galvanically isolated from supply and switching voltage 230W. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored in the memory functions when switching off. In the on-max functions is always switched on with maximum brightness level. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the

Universal power surge dimming switch for installation and AP mounting for R, L and C loads up to 400 W depending on the ventilation conditions, autom. detection of load type R+L or R+C, with %-Drehschalter the minimum brightness (fully dimmed) can be set, the set brightness stage remains stored when switching off, automatic electronic overload protection and over temp shutdown, children's room and slumber circuit, switching in zero-crossing with soft-on and soft-out for lamp protection, control inputs for light scanners, etc. Light switch, without N connection, stand-by loss only 0.7 W universal dimming switch 230V without N connection. Without N connection, Power MOSFET up to 400W. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R, L and C loads up to 400W, depending on the ventilation conditions. Automatic detection of load type R+L or R+C. Energy saving lamps ESL cannot be switched with dimmers without N-connection. Control voltage 230V. Minimum load 40W. Switch in zero passage with soft-on and soft-out for lamp protection. With %-Drehschalter the minimum brightness (fully dimmed) can be set. The dimming speed can be set with the dim speed rotary switch. At the same time, the duration of soft-on and soft-off is changed. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. In the event that light switches cannot be replaced by light switches, a separate control system is

Universal dimming switch without N connection, Power MOSFET up to 200W. Stand-by-Lower only 0.5 W, with control inputs for light sensor and light switch, minimum brightness, mode of operation and dimming speed adjustable, in the event that light switch cannot be replaced by light sensor, a separate control input for light switch is present, with children's room circuit, and slumber circuit nominal voltage: 230 W Color: blue Operation type: rotary knob Halogen-free: Yes Load type: universal. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. Minimum brightness, operating mode and dimming speed adjustable. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R and C loads up to 200W, depending on the ventilation conditions. Dimmable ESL and 230V LED lamps in the operating mode phase section up to 200W or in the operating mode phase section up to 40W, depending on the ventilation conditions. In the case of dimmable 230V LED lamps, which also light slightly in the switched-off state, a basic load element GLE must be connected parallel to the lamp. L-loads (inductive loads, for example wound transformers) must not be connected. Switching in the zero passage with soft-on and soft-out for lamp protection. Control voltage, supply voltage and switching voltage 230W. Minimum load 4W. Short control commands turn on/off, permanent control changes brightness up to maximum value. An interruption of the control changes the dimming direction. Set

Universal Dimming Switch Mounting type: Unterputz Color: blue Operation type: Rotary knob Halogen-free: Yes Composition: other load type: universal Serial dimmer: No Adjunct input: No Luminous accumulator: Yes Applicable with button: Yes Applicable with motion detector: No Applicable with presence detector: No Applicable with timer matt/timer: No Applicable with radio button: No. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1 Watt. Minimum brightness or dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Control voltage, supply voltage and switching voltage 230V. No minimum load required. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the upper %Lampe/dim-speed rotary switch can either set the dimming speed or the minimum brightness (fully dimmed). The dimming speed also changes the duration of soft-on and soft-off. During operation, the lower rotary switch determines whether automatic lamp detection is effective