List of products by brand Eltako

Blisterpack Dimmes with Tip-Funk® radio button TF-1FT and Tip-Funk® Universal Dimmor TF100D-230V. TF-1FT: 1-channel radio button pure white glossy for single mounting 84x84x16mm or assembly in the E-Design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Radio buttons with a rocker can send an evaluable signal: press rocker at the bottom in the area of the marking. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. TF100D-230V: Radio-Universal-Dimmaktor-Zwischenplug. 100x55x45mm (measures without plug), pure white. With Power MOSFET. 230 V-gloss and halogen lamps up to 300 W, 230 V-LED up to 100 W. No inductive (wound) transformers. With children's room and slumber circuit. No minimum load. Stand-by-loss only 0.7 Watt. Intermediate plug for German protective contact sockets with increased contact protection. Up to 24 radio universal probes, radio direction probes, radio central control probes and movement sensors TF-BSB as well as bidirectional radio can be learned with the comfortable tip radio technology. During learning, the dimmactor can be set to phase cut in order to allow optimum dimming for different LED lights. Mounting type: other number of outputs: 1 output power from/to: 300 - 300 W Voltage range: 230 - 230 W Frequency range: 50 - 50 Hz Version: Dimmactor load type: universal protection type (IP): IP20 Power additive usable: No Bus system EIB/KNX: No Bus system Radiobus: Yes Bus system Powernet: No Bus coupling inclusive: No Bus system LON: No Other bus systems: no

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. For single mounting 80x80x15/33mm
or assembly into the 55s switch system. Pure white glossy
With Power MOSFET. 230V and halogen lamps up to 300W,
230V LED lamps up to 100W. No inductive (wound) transformers.
With children's room and slumber circuit. With integrated universal
Direction sensor and connection for additional conventional probes.
Stand-by-loss only 0.7 Watt.

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. For single mounting 80x80x15/33mm
or assembly into the 55s switch system. Pure white glossy
1+1 Locker 4A/250V AC for one
Shading element motor.
With integrated universal/direction sensor and connection for additional
conventional probes.

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. For single mounting 80x80x15/33mm
or assembly into the 55s switch system. Pure white glossy
power surge switches with a lock, not potential-free,
230V bulbs and halogen lamps 1000W, ESL and 230V LED lamps up to
200W.

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. 84x84x16mm
or assembly into the e-design switch system. Pure white glossy
With Power MOSFET. 230V and halogen lamps up to 300W,
230V LED lamps up to 100W. No inductive (wound) transformers.
With children's room and slumber circuit. With integrated universal
Direction sensor and connection for additional conventional probes.
Stand-by-loss only 0.7 Watt.

Tip-Funk button actuators UP-Funk button actuator with rocker and frame. 84x84x16mm
or assembly into the e-design switch system. Pure white glossy
power surge switches with a lock, not potential-free,
230V bulbs and halogen lamps 1000W, ESL and 230V LED lamps up to
200W.

Radio-Dimmaktor Tipp-Funk® Universal-Dimmaktor, with Power MOSFET 230 V-Glüh- and halogen lamps up to 300 W, 230 V-LED up to 100 W, no inductive (wound) transformers, with children's room and slumber circuit, no minimum load, stand-by loss only 0.7 W, it can be possible to. With Power MOSFET. 230V-Glüh- und Halogen-Lampen bis 300W, 230V-LED bis 100W. No inductive (wound) transformers. With children's room and slumber circuit. No minimum load. Stand-by-loss only 0.7 Watt. With the comfortable Tip-Funk® technique, up to 24 radio universal probes, radio direction probes, radio central control probes and motion sensors TF-BSB can be learned. In addition, the actuator can be locally controlled with a conventional 230V controller without a glow lamp current. When learning, the dimmactor can be set to phase-section in order to allow optimum dimming with different LEDs.

Radio blind actuator Tip-Funk® blind and roller shutter actuator, 1+1 closer, 4 A/250 W AC, for a shading element motor. 45 x 45 x 18 mm, stand-by loss only 0.8 W, up to 24 radio universal probes, radio direction probes and radio central control probes as well as bidirectional radio can be learned with the comfortable tip-radio technique, in addition, the actuator can be locally controlled with a conventional 230 V control probe without glow lamp current. 45x45x18mm. Stand-by loss only 0.8 Watt. With the comfortable Tip-Funk® technology, up to 24 radio universal probes, radio direction probes and radio central control probes can be learned. In addition, the actuator can be locally controlled with a conventional 230V controller without a glow lamp current. H x B x T mm: 45 x 45 x 18 Rated voltage: 250 W

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours and the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1A. Time range from/to: 40 - 0.1 function: clock generator with pulse starting number of switches: 1 switching power incandescent lamps: 2000 W width in division units: 1 supply voltage range: 8 - 230 W switching power fluorescent lamps inductor: 1000 VA installation height: 58 mm switching power fluorescent lamps DUO: 1000 VA actuation type: analog with single function 1. Time unit: minutes/hour Mounting type: DIN rail Analog adjustable time relay. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. In the TGI12DX-UC type, a second multiplier t1 and t2 can be set separately at the same time basis. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence.

Rated voltage: 50 %. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA stairlight time switch, without switch-off warning. Stand-by-loss only 0.7 Watt. Time setting about 0.2 to 12 minutes. Own continuous light switch with the large rotary switch. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. Without disconnection and contact circuit in the zero passage. With double connections for probe and lamp, so that it can be connected either at the top and bottom or only at the bottom.

Number of hours:. Bulb load: 400 W Max. Fluorescent lamp load (parallel compensated): 400 VA stairlight time switch with switch-off warning and pushbutton continuous light can be switched on. Stand-by-loss only 0.7 Watt. With ESL optimization and multifunction. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. In addition, with galvanically separated universal control voltage. Automatic detection of the circuit type. Glow lamp current up to 50ma, depending on the ignition voltage of the glow lamps. Precise time setting 1 to 30 minutes with minute scale. Permanent light switch with the large rotary switch. After a power failure in the function setting

Steplight time switch, electronic for mounting on support rail DIN-EN 50 022, for older installations, for the control voltage 230W AC, very low switching noise, Glow lamp current 50ma, for 3-wire circuits, not switchable, without autom. Detection of the circuit type, with a relay for 2300W incandescent lamp load, continuous light switch, switch-off warning and push-button continuous light, contact circuit in the zero passage of the sine wave to the device and lamp-saving width in division units: 1 drop-back delay: 1 - 10 min Number of switches: 1 control voltage 1: 230 - W measurement switch current: 10 A control voltage type 1: AC. Bulb load: 2000 W Max. Lamp load: 1000 VA Max. Fluorescent lamp load (Duo circuit): 1000 VA Max. Fluorescent lamp load (parallel compensated): 500 VA stairlight time switch with switchable switch-off warning. Stand-by-loss only 0.7 Watt. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230W. Glow lamp current up to 50ma depending on the ignition voltage of the glow lamps. Precise time setting 1 to 12 minutes with minute scale. Own continuous light switch with the large rotary switch. For 3-wire circuits with attic lighting, not switchable. Only for retrofit

Steplight time scale for mounting on support rail DIN-EN 60715 TH35, 16 A/250 V AC not potential-free, incandescent lamps up to 2300 W, ESL and LED lamps up to 200 W, control voltage 230 V and/or 8..230 V UC, switch off pre-warning and pushbutton continuous light, standby loss adjustable only 0.5 Watt. Stand-by-loss only 0.7 Watt. With ESL optimization and multifunction. The functions and times are entered according to the user manual with the MODE and SET keys and displayed digitally on the -LC display. A key lock is possible. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. The noiseless electronics do not harass the most sensitive ear, unlike many synchronous motors with mechanical transmission. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230V. In addition with galvanically separated universal control voltage 8..230V UC. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. Glow lamp current up to 50mA, depending on the ignition voltage of the glow lamps. Precise time setting 1 to 99 minutes. Own continuous light button with the protruding button SET in the functions TLZ, ESV, ES and ER. With motion detector control input BM, which converts the input signal into a control pulse in the function TLZ. Width in division units: 1 Relapse delay: 1 - 1 min Function: electronic with multifunction Assembly type: DIN rail Number of locks: 1 Control voltage 1: 230 - 23

Steplight time switch, electronic for installation and AP installation, 10A/250V AC, control voltage 230W AC, Glow lamp current 50ma, with pumps, switch-off warning and pushbutton continuous light, in addition the function: current surge switch with drop-back delay ESW, contact circuit in the zero crossing of the sine wave to the device and lamp-saving stairlight time switch 230W. 1 lock not potential-free 10A/250V AC, incandescent lamps up to 2000W, ESL and LED lamps up to 200W, switch-off warning and push-button continuous light. Stand-by-loss only 0.7 Watt. With ESL optimization.For installation. 45mm long, 45mm wide, 18mm deep. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230W. Time setting 1 to 12 minutes. Glow lamp current up to 50ma, depending on the ignition voltage of the glow lamps. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. After a power failure, the illumination is switched on again when the time sequence has not yet been completed. When switched off, the lighting flickers approx. 30 seconds before the time sequence beginning and a total of 3 times in shorter time intervals. When the pushbutton permanent light is switched on, it is possible to set for longer than 1 second by means of buttons, which is switched off automatically after 60 minutes or can be switched off with buttons for longer than 2 seconds. If the pushbutton continuous light and the switch-off pre-warning are switched on, the switch-off pre-warning takes place after the switch-off of the continuous light. Become a full or part

Steplight time switch, electronic for UP mounting, built-in device quietly and timely, max. 50ma Glow lamp current, time range stepless to 10 minutes adjustable, 4-wire switchable, rated switching power 10 A/250 W AC, control voltage 8...230 W UC Stair switch 230V+UC. 1 lock not potential-free 10A/250V AC, incandescent lamps up to 2000W, ESL and LED lamps up to 200W, switch-off warning and push-button continuous light. Stand-by-loss only 0.7 Watt. With ESL optimization. For installation. 45mm long, 45mm wide, 18mm deep. Contact circuit in the zero passage for protecting the contacts and lamps. In particular, this extends the service life of energy-saving lamps. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Control, supply and switching voltage 230W. In addition with galvanically separated universal control voltage 8..230V UC. Time setting 1 to 12 minutes. Glow lamp current up to 50ma, depending on the ignition voltage of the glow lamps. For 3- and 4-wire circuits, switchable, with attic lighting at 4-wire circuit. Automatic detection of the circuit type. After a power failure, the illumination is switched on again when the time sequence has not yet been completed. When switched off, the lighting flickers approx. 30 seconds before the time sequence beginning and a total of 3 times in shorter time intervals. When the pushbutton permanent light is switched on, it is possible to set for longer than 1 second by means of buttons, which is switched off automatically after 60 minutes or can be switched off with buttons for longer than 2 seconds. If the pushbutton continuous light and the switch-off pre-warning are switched on, the switch-off pre-warning takes place after the switch-off of the continuous light. All or part of