Best sellers

1P+N 10kA B- 16A 30mA type A-G fault current circuit breaker according to EN 61009-1 and EN 61009-2-1, short-term delayed according to ÖVE E 8601. IP2x contact protection according to DIN VDE 0660 part 514. Suitable for subsequent mounting of additional devices (mount without tool). Connection terminals with wire insertion protection, Bi-Connect terminals below, external blue test button for half-yearly actuation and fault current display. Easy removal from the phase rail composite. All products with ÖVE characters. Labeling option directly on the device. Nominal current: 16 A Trigger characteristic: B Switching capacity Icn AC according to IEC 60898-1: 10 kA type of fault current protection: A G Rated fault current: 30 mA Number of poles: 2 P Number of modules: 2 Rated operating voltage Ue: 230 V

Siemens 5ST0001-3AA10 3-Phasen Stift-SS N 1014mm, 10mm²

Thermoplastic flame-retardant material, IP55 with condensation water opening, bottom inserts M20, external fastening points, opening cutter, halogen-free, protection type: IP 54, application temperature range: -25 °C to 40 °C, color: grey. Depth: 37 mm. Length: 75 mm Width: 75 mm Depth: 37 mm Number of inserts: 7

Wiring bridges AE/AE Finished wiring bridges on both sides. For wiring of LS,- FI,- and similar switching devices. For example, for installation small distributors and counter positions according to WDE 0603. Standards: EN 60439-1 / WDE 0660, part 500 .Power-bearing capacity: WDE 0100, part 523: 6 mm2: max. 54 A. Rated voltage: 450 / 750 W. Insulation material: PWTSC (type of lead H07V-K). Head: Flexible. Cable end: Aderend sleeve on both sides.Colour: blue.

Conductor terminals for mounting on DIN rails, e.g. for small installation distributors and counters acc. VDE 0603. 35/25 mm2. 1-pole. Classy. Mounting on 35 mm support rail according to. EN 60715 / EN 50022. Installation small distributor and counter positions AC 400V. Main line branch terminals VDE 0603-2, connection material for low voltage circuits for household and similar purposes VDE 0613, Part 1 / EN 60998-1. Color coding corresponding to valid vein colors. Mounting horizontally or vertically. Insulation voltage: 1000 V AC / DC for: Overvoltage category III (Uimp = 8 kV, fixed installation), level of contamination 2 (e.g. distributor installation). VDE certified (VDE 0613, Part 1 / EN 60998-1): Test current 125 A. Suitable for Cu and Al conductors. Clamp: brass (galvanized). Clamp screws: steel, galvanized. Insulation housing: plastic (polyamide), impact-resistant, flame-resistant, halogen-free. Line connection: - Main line: 10 - 35 mm2 rigid/multi-wire, 3.5 Nm - branch line: 1.5 - 25 mm2 rigid/multi-wire, 2.5 Nm - stripping length: 25 mm. Inputs max. 35 mm2: 2. Outputs max. 25 mm2: 6. Bushing clamp with 2 screws per clamping point, screws with combination slot Pozidriv Z2. Corners rounded. miter protection: IP20, fingerproof

Conductor terminals for mounting on DIN rails, e.g. for small installation distributors and counters acc. WDE 0603. 35/25 mm2. 1-pole. Classy. Mounting on 35 mm support rail according to. EN 60715 / EN 50022. Installation small distributor and counter positions AC 400W. Main line branch terminals WDE 0603-2, connection material for low voltage circuits for household and similar purposes WDE 0613, Part 1 / EN 60998-1. Color coding corresponding to valid vein colors. Mounting horizontally or vertically. Insulation voltage: 1000 W AC / DC for: Overvoltage category III (Uimp = 8 kw, fixed installation,) Level of contamination 2 (e.g. distribution installation). WDE certified (WDE 0613, Part 1 / EN 60998-1): Test current 125 A. Suitable for Cu and Al conductors. Clamp: brass (galvanized). Clamp screws: steel, galvanized. Insulation housing: plastic (polyamide,) impact-resistant, halogen-free. Line connection: - Main line: 10 - 35 mm2 rigid/multi-wire, 3.5 Nm - branch line: 1.5 - 25 mm2 rigid/multi-wire, 2.5 Nm - stripping length: 25 mm. Inputs max. 35 mm2: 2. Outputs max. 25 mm2: 6. Bushing clamp with 2 screws per clamping point, screws with combination slot Pozidriv Z2. Corners rounded. miter protection: IP20, fingerproof

Type of cable: 36 mm

Universal Bus Dimming Switch for mounting on DIN-EN 60715 TH35 Power MOSFET up to 400 W, for lamps up to 400 W, depending on the ventilation conditions, dimmable energy saving lamps ESL and dimmable 230 V-LED lamps additionally depending on the lamp electronics, automatic lamp detection, minimum or maximum brightness and dimming speed adjustable, children's room and slumber circuit width. Stand-by loss only 0.3 Watt. Minimum brightness, maximum brightness and dimming speed adjustable. With children's room and slumber circuit. 1 division unit. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps and dimmable 230V LED lamps additionally depend on lamp electronics. Up to 3600W with power inputs at terminals X1 and X2. The control inputs are galvanically separated from the supply and switching voltage. Switching in the zero passage with soft-on and soft-out for lamp protection. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. From 110W control voltage glow lamp current 5ma (not at RTD). Automatic electronic overload protection and overtemperature shutdown. The functions and times are entered according to the user manual with the MODE and SET keys and displayed on the LC display. A key lock is possible.

Multifunction universal dimming switch for installation and AP mounting for R, L and C loads up to 400 W, Power MOSFET up to 400 W, dimmable energy saving lamps ESL up to 100 W, depending on the ventilation conditions, automatic lamp detection, standby loss only 0.1 W, minimum brightness adjustable, child's room and slumber circuit, standby loss only 0.1 Watt. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1Watt. Minimum brightness adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Universal control voltage 8..230V UC, galvanically isolated from supply and switching voltage 230W. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored in the memory functions when switching off. In the on-max functions is always switched on with maximum brightness level. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the

Phase rail 3 pole + N, 2-row 125mm, left, vertical

High-quality fault current protection switches/control protection switches Combination without voltage, contact position indicator red - green, clamping aid - back plug protection, tristable snap-in slides - enables expansion from an existing interlocking system, peripheral accessory program to be retrofitted, large selection of dimension fault currents, dimensioning currents up to 40 A, triggering characteristics B, C, dimensioning switching capacity 10 kA, suitable for use in outdoor air distribution (convection)

Frame 3x Q.1 polar white, velvet. Cover frame for vertical and horizontal mounting. For use of polar white central pieces. Underput installation, area program, 3-fold. Material: plastic, thermoset, halogen-free. Cover frame for vertical and horizontal mounting. For use of polar white central pieces. Underput installation, area program, 3-fold. Material: plastic, thermoset, halogen-free.