Best sellers

1P+N 10kA B- 13A 30mA type A-G fault current circuit breaker according to EN 61009-1 and EN 61009-2-1, short-term delayed according to ÖVE E 8601. IP2x contact protection according to DIN VDE 0660 part 514. Suitable for subsequent mounting of additional devices (mount without tool). Connection terminals with wire insertion protection, Bi-Connect terminals below, external blue test button for half-yearly actuation and fault current display. Easy removal from the phase rail composite. All products with ÖVE characters. Labeling option directly on the device. Nominal current: 13 A Trigger characteristic: B Switching capacity Icn AC according to IEC 60898-1: 10 kA type of fault current protection: A G Rated fault current: 30 mA Number of poles: 2 P Number of modules: 2 Rated operating voltage Ue: 230 V

Counter clamp AC 50A counter connection clamp designed as a counter clamp for the fast and secure installation and arm of energy meters of different manufacturers and systems with counter pin spacing according to DIN 43857. The counter clamp was tested according to ÖVE R21:2015 with 50A rated current when using the standard pin and is available with an extensive accessory.

Relay mount with screw connections, for DIN rails, for relays ,40.52, 40.61, 44.52 or 44.62, module series 99.80, color black

FI-Schutzschalter, 4-polig,Typ A, kurzzeitverzögert, In:40 A, 30 mA, Un AC: 400 V, nicht vorsicherbar

Main line branch terminals 35/25 mm2, 1-pole. Classy. Mounting on 35 mm support rail according to. EN 50022 / EN 60715. For example, for installation small distributors and counter positions according to WDE 0603. Installation small distributor and counter positions AC 400W. Main line branch terminals WDE 0603-2, connection material for low voltage circuits for household and similar purposes WDE 0613, Part 1 / EN 60998-1. Color coding corresponding to valid vein colors. Mounting horizontally or vertically. Voltage: 1000 W. WDE certified. Suitable for Cu and Al conductors. Inputs max. 35 mm2: 2nd outputs max. 25 mm2: 2nd clamping body: brass, (galvanized). Clamp screws: steel, galvanized. Insulation housing: plastic, (polyamide) impact-resistant, halogen-free. Main line 10 - 35 mm2 rigid/several, 3.5 Nm. Cutting line: 1.5 - 25 mm2 rigid/multiplier, 2.5 Nm. Stripping length 25 mm. Bushing clamp with 2 screws per clamping point screws with combination slot Pozidriv Z2. IP 20, fingerproof. Corners rounded. Number of poles: 1 Colour: grey

NH00 Locking inserts with metal handle tabs NH00 Low-voltage protection, according to DIN WDE 0636 Part 2, nominal voltage: 500W AC / 220W DC, width: up to 100A 20 mm / from 125A 30 mm, NH000 to 100A / NH00 from 125A, voltage-carrying grip tab, operating class (gL)-gG full-range safety inserts (for cable and cable protection) for general applications

Base load element resistance block, PTC in a small socket with connection lines, can be used directly in a consumer, a switch or a branch box, it is not able to hold the field-free switch on without additional consumers A basic load is used if consumers cannot be detected due to their capacity, but should cause the mains voltage to be switched on. Basic loads must always go into operation parallel to the associated consumer and be switched off with the same. Higher standby loads can impair or prevent recognition of a basic load. Examples of this: fluorescent lamps, dimmer circuits and electronic transformers. Basic load element GLE PTC in a small sleeve with connection lines can be used directly in a consumer, a switch or a branch can. It is not able to hold the field-free switch on without additional consumers.

PVC-isolierte Starkstromkabel 0,6/1kV Verwendung: Als Energiekabel für feste Verlegung, vorzugsweise in Kabelkanälen und Innenräumen, im Freien, im Wasser, in Erde, wenn keine nachträglichen Beschädigungen zu erwarten sind.

PVC Schlauchleitung Verwendung: In trockenen sowie in feuchten und nassen Räumen bei mittleren mechanischen Beanspruchungen für den Anschluss von Elektrogeräten z.B. Waschmaschinen,Kühlschränke usw. jedoch nicht für Wärmegeräte, bei denen die Gefahr besteht, dass die Leitung mit heißen Teilen in Berührung kommen kann

Clamp with protective conductor contact for connecting or connecting wires, wires and cables with permanently secure contact. Hardened steel for mechanical forces and high-quality copper with tin coating ensure the best conductivity.

The terminal plate serves for the optical separation of circuits and the prevention of wiring errors, as well as the protection of contact between voltage-carrying parts.

Adhesive clamp suitable for pipes with 3/8 to 4 inches diameter. The clamp body, the screws and the clamping strap are made of stainless steel (VA). Connections: max. 2 lines 2,5-25 mm2. RD 8.