List of products by brand Eltako

Universal power surge dimming switch for installation and AP mounting for 230V incandescent lamps and halogen lamps, for NV halogen lamps with inductive transformers and with electronic transformers up to 400W as well as for dimmable energy saving lamps in the setting ESL to 100W, with rotary switches the minimum brightness can be set, at the same time the duration of soft-on and soft-off switch is changed, children's room and slumber. Power MOSFET up to 400W. Automatic lamp detection. Stand-by loss only 0.1 Watt. Minimum brightness or dimming speed adjustable. With children's room and slumber circuit. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for lamps up to 400W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Universal control voltage 8..230V UC, galvanically isolated from the supply and switching voltage 230V. No minimum load required. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. With the upper %Lampe/dim-speed rotary switch can either set the dimming speed or the minimum brightness (fully dimmed). The dimming speed also changes the duration of soft-on and soft-off. During operation, the lower rotary switch determines whether the automatic lamp recognition should work or special comfort positions: AUTO allows the dimming of all lamp types. EC1 is a comfort site

Energy consumption indicator for series installation The energy consumption indicator EVA12 measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories Eltako- AC counters of class B at MID (1%), the starting current is 20 mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Up to 24 hours, up to 31 days, up to 12 months and up to 24 years can be completed. The memory can be reset. Maximum current (value): 32 A Energy consumption display with display - smart metering for support rail. Stand-by loss only 0.5 Watt. The energy consumption indicator measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories. The accuracy corresponds to all Eltako- AC counters of class B at MID (1%), the starting current is 20mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Totalreset: In order to start storing the values in exact hours, a total set is recommended at a reasonable time after installation. To do this, hold the MODE and SELECT keys simultaneously for 5 seconds until RES appears in field 1. If SELECT is now briefly pressed, all memories are set to zero. After that, the program automatically returns to the normal display.

Radio sensor for single mounting 84 x 84 x 16 mm or assembly in the e-design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Funktaster wg pure white glossy for single mounting 84x84x16mm or mounting in the e-design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1E, a rocker, a double rocker, a fastening frame, a holding plate, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first glue the set holding plate with frame and fastening frame with the latches on top and bottom. Then the set radio module with rocker ? Marking 0 on the back always snap in top. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then screw the holding plate - with the latches at the top and bottom -, snap the frame with the fastening frame and snap the set radio module with rocker - marking 0 on the back always at the top. The radio module contained in the radio button can

Radio antenna with magnetic foot small attached radio antenna of the radio antenna module FAM12, radio antenna switch actuator FAA12 or radio antenna switch actuator FAB12 can be replaced by a larger antenna for the introduction of the radio signals in metal switch cabinets, is mounted externally with a magnetic foot and the 250 cm long cable is guided inward to the FAM12, FAA12 or FAB12 only. The small adjacent radio antenna of the radio antenna modules and some radio transmitter modules can be exchanged for receiving or transmitting the radio signals in or out of metal switch cabinets for these larger 868Mhz-HF antennas. It is mounted externally with a magnetic foot and the 250cm long cable is guided inward. The best performance is achieved if it adheres to a metal surface with the magnetic foot. The transmission and reception area is almost spherical around this antenna. Height of the antenna only 10cm. With SMA screw connection. Frequency range: 868 - 868 Mhz

Radio antenna module for mounting on support rail DIN-EN 60715 TH35, forwards all radio signals addressed to downstream radio actuators in its receiving area, mini-USB for connecting a PC for creating a device list, for configuring the actuators using the PCT14 PC tool and for data backup, supply voltage 12V DC radio antenna module for the Eltako-RS485 bus with interchangeable antenna. With integrated power supply 12V DC/8W. Bidirectional. Encrypted radio. Stand-by-loss only 1 watt. If required, a radio antenna FA250 or FA200 can be connected. Row mounting device for mounting on support rail. 36mm wide, 58mm deep. Supply voltage 230V. Included are 2 terminal resistors for mounting with imprint, 1/2 TE, 3 plug-in bridges 1 TE (including 1 replacement), 2 plug-in bridges 1/2 TE (including 1 replacement) and a plug-in bridge mounting tool SMW14. The radio antenna module FAM14 receives and checks all signals from the radio transmitters and repeaters in its reception area. These are passed through an RS485 interface to downstream RS485 bus switch actuators: Up to 126 channels can be connected to the RS485 bus. Bus and power supply with plug-in bridge. At the last actuator, the adjacent second terminal resistor must be plugged on. Up to 128 encrypted sensors can be learned. Mini USB to connect a PC to create a device list, to configure the actuators using PCT14 and to backup data. A legalization code for downloading the PCT14 from the Eltako-Homepage www.eltako.de is attached to FAM14. With a load greater than 50% of the rated power of 8W, half a division unit is required for ventilation with the spacer DS14 on the left side. TLE: 2 radio frequency: 868 MHz

Bus couplers for wire connections of the bus and power supply bridges, for mounting on support rail DIN-EN 60715 TH35, cross wiring bus and power supply with plug-in bridge, can connect both different bus parts and feed in power supplies, bus parts on different support rails or in other distributors or switch cabinets are each connected with an FBA14 and a 4-wire shielded bus line, e.g. a telephone line. Bus and power supply with plug-in bridge. The bus coupler FBA14 can connect both different bus parts and feed power supplies. Bus parts on different support rails or in other distributors or control cabinets are each connected to an FBA14 and a 4-wire shielded bus line, for example a telephone line. The total length of all connecting lines should not exceed 100m and the only 9mm wide 2nd final resistance to the FAM14 or FTS14KS must be plugged onto the last actuator. The position of the bus coupler in a series of devices of the series 14 is arbitrary.

Radio motion brightness sensor for ceiling mounting, the radio motion brightness sensor FBH, supplied with a solar module, sends a message into the ELTAKO radio motion brightness sensor for splash mounting 84x84x39mm or assembly into the E-design switch system. Power supply with the integrated solar cell or with a 12VDC power supply or with batteries. In the delivery state, the energy store is empty and must be charged before commissioning. Either via the red-black 12W DC connection cable in approx. 3 minutes or via the solar cell in bright daylight approx. 10 hours or by inserting two AAA batteries (not included) in about 10 minutes. In normal operation, the power supply takes place either via the connection cable with a 12W DC switching power supply FSNT61-12V/6W in an UP-dose under the sensor or with AAA batteries, supported by the solar cell, or only with the solar cell with normal ambient brightness, in the daily average at least 200 lux. If only the solar cell is available, the energy store must be charged several days with daylight. If the connection cable is not required, it can be cut off. As a result, the sensor does not require any installation depth behind the holding plate and can be screwed onto any flat surface. For screwing on, the complete module can be pulled out of the frame. 2 pieces stainless steel counter screws 2.9x25mm and 5x25mm dowels are included. For learning into an actuator located in the learning mode, the adjacent blue or any other available magnet is held to the side wall below the point of the sensor marked with a rectangle. This sends a learning message. A red LED behind the Fresnel lens confirms the transmission of the learning telegram by short flashing. The sensor measures from 0 to 2000 Lux and sends every 100 seconds at a brightness change of at least. 10 Lux a Meldu

Radio transmitters the batteryless remote control contains 2 same radio modules as the radio button FT4 and has 2 double rockers, therefore it is possible to send 8 evaluable radio telegrams Color: aluminum anthracite Number of channels: 8 Window transmitters: No Suitable for display element: No Hand transmitter: Yes Wall transmitter: No Remote control: Yes Halogen-free: Yes Finishing of the surface: matte. The batteryless remote control contains two identical radio modules and has 2 double rockers. 8 evaluable radio telegrams can therefore be sent. A wall bracket WHF-al and 2 pieces stainless steel countersink screws 2.9x25mm and dowel 5x25mm are included for wall mounting. The rockers can be simply pulled off and replaced by laser-engraved rockers.

Bus gateway multiple gateway, bidirectional, stand-by-loss only 0.5 watts, for coupling in up to 3 FEM, up to 10 FTS12EM, for direct connection with the computer GFVS-Safe, for connection with the bus components of the series 12, an RS232 interface or as a bus connector of two RS485 buses of the series 14, connection to the Eltako-RS485 bus, cross wiring bus and power supply with multiple gateway. Bidirectional. Stand-by loss only 0.5 Watt. Row mounting device for mounting on support rail. The gateway is only 1 TE wide but can be used multiple times: for coupling up to three radio reception modules, for direct connection via the RS232 interface to the PC, for connection with the bus components of the older series 12 or as a bus connector of two RS485 buses of the series 14. Connection to Eltako-RS485-Bus. Cross-wiring bus and power supply with plug-in bridge. The hold terminal is connected to the FAM14 or FTS14KS. Radio reception modules are connected in parallel to the sub-bus terminals RSA2 and RSB2 as well as the power supply terminals GND and +12V. Up to 10 probe input modules FTS12EM are optionally connected in series to the sub-bus terminals RSA2 and RSB2, possibly in series with radio reception modules FEM. The PC connection is effected by connection to the terminals Tx and Rx. Series 12 actuators are connected to the RSA2 and RSB2 sub-bus terminals. There is no hold connection here. A second series 14-bus is fed via the terminals RSA2/RSB2. The settings of the operating mode rotary switch BA take place according to the operating instructions. TLE: 1

Protection type (IP): IP20 Radio frequency: 868 Mhz Range: 30 m Number of commands: 2 Power supply: other Rolling code system: No Radio transmitter: No Radio button under plaster: No Radio button on plaster: Yes Radio coder: No Radio-Hoppe window handles Secusignal series Atlanta with integrated radio transmitter module, battery- and wireless. Create the radio telegrams even when opening, tilting and closing the windows. The complete assembly material is included. The radio sensor can be learnt in the following actuators and in the building radio visualization and control software: F2L14, F4HK14, FGM, FHK14, FHK61, FMZ14, FMZ61, FSB14, FSB61, FSB71, FSG14, FSR14, FSR61, FSR71, FUA FDD14 FUTH.

Radio actuator heating-cooling relay for can installation, 1 closer potential-free 10A/250V AC. Stand-by loss only 0.3-0.8 watts. For installation. 45mm long, 55mm wide, 33mm deep. Supply voltage 230 W or 8 to 24 W UC. Radio actuator heating cooling relay 230W. 1 Locker potential-free 10A/250V AC. Stand-by loss only 0.8 Watt. Encrypted radio, bidirectional radio and repeater function can be switched on. For installation. 45mm long, 45mm wide, 33mm deep. If the supply voltage fails, the switching state is maintained. When the supply voltage is recurring, it is switched off in a defined manner. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. This heating-cooling relay evaluates the information from radio temperature controllers or sensors. Optionally complements window door contacts, motion detectors, hoppe window handles and radio buttons. Valves are controlled with the potential-free working contact. From the manufacturing week 11/14, encrypted sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. Each function change (normal operation, lowering operation, out) is confirmed with a radio telegram. This radio telegram can be learned in the GFVS software. Upper rotary switch for operating modes. The LED accompanies the learning process according to the user manual and displays radio control commands during operation by short flashing. Mounting type: Approval Radio frequency: 868 Mhz Colour: blue Material: plastic Halogen-free: Yes Material quality: thermoplastic Finishing of surface: matt Suitable for dimmer: No Suitable for pulse pushers: No Suitable for roller shutter switch: No Suitable for switch: No In the case: Yes In the tube socket housing: No As module/plate: No Touch operation: No Switching operation: No With radio hand switch: Yes

Wireless radio hand transmitter, can be glued to the wall, on glass or on furniture with an adhesive film, with 2 label labels for the back and 1 adhesive film. The radio modules contained in the radio hand transmitter can, according to the user's instructions, be learned in encrypted form in all encryptable actuators of the series 61 and 71, as well as in the FAM14. Color: white Number of channels: 8 Window transmitter: No Suitable for display element: No Hand transmitter: Yes Wall transmitter: No Remote control: Yes Halogen-free: Yes Surface design: shiny Suitable for switches: Yes Suitable for dimmer: Yes Suitable for blind switches: Yes Radio transmitter, 154x50mm, 16mm high. The batteryless hand transmitter contains two same radio modules as the radio button FT4 and has 2 double rockers. 8 evaluable radio telegrams can therefore be sent. This radio hand transmitter can also be glued to the wall, to glass or to furniture with an adhesive film as well as the non-conductive radio buttons. Includes 2 labeling labels for the back and 1 adhesive film. The radio modules contained in the radio hand transmitter can, according to the user's instructions, be learned in encrypted form in all encryptable actuators of the series 61 and 71, as well as in the FAM14. For this purpose, the radio-taster encryption rocker FTWW is required. Encryptable actuators carry the key pictogram.

Radio actuator for installation, dimming switch for LED 12-36V DC, up to 4A, stand-by loss only 0.2-0.4 Watt, minimum brightness and dimming speed adjustable, with children's room and slumber circuit, additionally with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function connectable PWM dimming switch for LED 12-36VDC, up to 4A stand-by loss only 0.2-0.4 Watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. In addition with light scene control via PC or with radio buttons. Encrypted radio, bidirectional radio and repeater function can be switched on. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage 12 to 36V DC, depending on the connected LED illumination. Output voltage PWM (pulse-width modulation). Output current max. 4A. A pulse-resistant DC power supply is required which supplies the required voltage and the required current of the LED lamp(s). Universal control voltage 8..230V UC, galvanically isolated from the supply and switching voltage. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. From the manufacturing week 11/14, encrypted sensors can be learned. Bidirectional radio and/or a repeater function can be switched on. With the upper %Lampe The minimum brightness (fully dimmed) can be set. In the LRN position, up to 35 radio buttons are assigned, one or more central control buttons thereof. The dimming speed can be set with the lower dim speed rotary switch. In addition to the radio control input via an internal antenna, this dimming switch can also be equipped with an event

Radio minihand transmitter 43x43mm, 16mm high. Weight only 30 grams. The batteryless mini-hand transmitter FMH2 has 1 rocker. Therefore, 2 evaluable radio telegrams can be sent. The rocker is laser-engraved with 0 and I. This radio hand transmitter can also be glued to the wall, to glass or to furniture with an enclosed adhesive film. The mini hand transmitter is supplied with the following engraving: top 0 (= from) and bottom I (= one). Colour: white Range: 30 m Signal transmission: radio Number of channels: 2 Mounting type: Other material: Plastic Material quality: Thermoplastic Window transmitter: No Suitable for display element: Yes Hand transmitter: Yes Wall transmitter: Yes Remote control: Yes Halogen-free: Yes Surface: untreated Surface finish: glossy Suitable for switches: Yes Suitable for dimmer: Yes Suitable for blind switch: Yes

Radio mini hand transmitter ws white, 43x43mm, 16mm high. Weight only 30 grams. The batteryless mini hand transmitter contains the same radio module as the radio button FT4 and has 1 rocker. Therefore, 2 evaluable radio telegrams can be sent. The rocker is laser-engraved with 0 and I. This radio hand transmitter can also be glued to the wall, to glass or to furniture with an enclosed adhesive film. It is additionally prepared for attaching a key tag. The mini hand transmitter is supplied with the following engraving: top 0 (= from) and bottom I (= one). According to the user manual, the radio module contained in the radio minihand transmitter can be learned in encrypted form into all encryptable actuators of the series 61 and 71 as well as into the FAM14. For this purpose, the radio-taster encryption rocker FTWW is required. Encryptable actuators carry the key pictogram. Colour: white Range: 30 m Signal transmission: radio Number of channels: 2 Installation type: other material: plastic Material quality: thermoplastic Window transmitter: No Suitable for display element: Yes Hand transmitter: Yes Wall transmitter: No Remote control: Yes Halogen-free: Yes Surface: untreated Surface finish: matt Suitable for switch: Yes Suitable for dimmer: Yes