Eltako

80 x 80 mm outside, frame internal dimensions 63 x 63 mm, 15 mm high. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss area radio button, 80x80mm outside, frame internal dimensions 63x63mm, 15mm high. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1F, a surface rocker WF, a surface double rocker DWF (all the same color), a fastening frame BRF, the holding plate HP, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then screw the holding plate - with the latches at the top and bottom -, snap the frame with the fastening frame and snap the set radio module with rocker - marking 0 on the back always at the top. We recommend Edelsta

80 x 80 mm outside, frame internal dimensions 63 x 63 mm, 15 mm high. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss Number of channels: 4 Color: pure white Signal transmission: Mounting type: Material: Material quality: Range: 30 m Window transmitter: No Suitable for display element: No Hand transmitter: No Wall transmitter: Yes Remote control: No Halogen-free: Yes Surface design: matt Suitable for switches: Jammy size 80. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1F, a surface rocker WF, a surface double rocker DWF (all the same color), a fastening frame BRF, the holding plate HP, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing the frame with fastening

Multifunction power surge relays can be selected with potential-free 10A/250V AC, incandescent lamps 2000W, no stand-by loss, for installation and AP installation, hybrid technology, universal control voltage 8..230V UC, no constant power supply is required, therefore no stand-by loss, due to the use of bistable relays there can also be no coil loss power in the switched-on state and no heating. 1+1 lock potential-free 10A/250V AC, light bulbs 2000W. No standby loss. For installation. 45mm long, 45mm wide, 32mm deep. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. Universal control voltage 8..230V UC. No constant power supply required, therefore no stand-by loss. Due to the use of bistable relays, there is no coil loss power and no heating thereby even in the switched-on state. The relay contact can be open or closed during commissioning and synchronizes during the first actuation. The functions of the second rotary switch are preselected with the ES/ER rotary switch. ER selects the clamp functions. It can be selected between 10 functions: 2S = current surge switch with 2 locks. (2R) = switching relay with 2 locks. WS = power surge switch with 1 lock and 1 opener. (WR) = switching relay with 1 lock and 1 opener. SS1 = series switch 1+1 lock with switching sequence 1. (RR) = switching relay (super current relay) with 2 openers. SS2 = series switch 1+1 lock with switching sequence 2. (EW) = turn-on wiper relay with 1 lock and 1 opener, wiping time 1s. GS = groups

Control dimming switch for EVG not potential-free 600VA and 1-10V control output 40mA. Stand-by-loss only 1 watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. In-line construction equipment for mounting on support rail DIN-EN 60715 TH35. Universal control voltage 8..230V UC, locally and centrally with the same potential. Supply voltage 230V galvanically separated. The latest hybrid technology combines the advantages of wear-free electronic control with high power of special relays. Switching in the zero passage for contact protection. 1-10V control dimming switch for EVG. 1-10V control output 40mA. Stand-by-loss only 1 watt. Minimum brightness and dimming speed adjustable. With children's room and slumber circuit. Also for controlling LED converters with passive 1-10V interface without auxiliary voltage up to 0.6mA. On top with auxiliary voltage. Locally and centrally one/off with the same potential. Supply voltage galvanically separated. The latest hybrid technology combines the advantages of wear-free electronic control with high power of special relays. Switching in the zero passage for contact protection. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and it is switched on when the supply voltage is returned. With %-Drehschalter the minimum brightness (fully dimmed) can be set. At the same time, it is determined whether the children's room circuit and the slumber circuit are active (+KI +SL). The dimming speed can be set with the dim-speed rotary switch. The load is switched on and off with a bistable relay at the output EVG. Switching power fluorescent lamps or NV halogen lamps with EVG 600VA. Due to the use of a bistable relay, there is no coil loss power and no heating heredur

Universal power surge dimming switch for installation and AP mounting for R, L and C loads up to 400 W depending on the ventilation conditions, autom. detection of load type R+L or R+C, with %-Drehschalter the minimum brightness (fully dimmed) can be set, the set brightness stage remains stored when switching off, automatic electronic overload protection and over temp shutdown, children's room and slumber circuit, switching in zero-crossing with soft-on and soft-out for lamp protection, control inputs for light scanners, etc. Light switch, without N connection, stand-by loss only 0.7 W universal dimming switch 230V without N connection. Without N connection, Power MOSFET up to 400W. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R, L and C loads up to 400W, depending on the ventilation conditions. Automatic detection of load type R+L or R+C. Energy saving lamps ESL cannot be switched with dimmers without N-connection. Control voltage 230V. Minimum load 40W. Switch in zero passage with soft-on and soft-out for lamp protection. With %-Drehschalter the minimum brightness (fully dimmed) can be set. The dimming speed can be set with the dim speed rotary switch. At the same time, the duration of soft-on and soft-off is changed. Short control commands turn on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction. The set brightness level remains stored when switching off. In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. In the event that light switches cannot be replaced by light switches, a separate control system is

Radio mini hand transmitter ws white, 43x43mm, 16mm high. Weight only 30 grams. The batteryless mini hand transmitter contains the same radio module as the radio button FT4 and has 1 rocker. Therefore, 2 evaluable radio telegrams can be sent. The rocker is laser-engraved with 0 and I. This radio hand transmitter can also be glued to the wall, to glass or to furniture with an enclosed adhesive film. It is additionally prepared for attaching a key tag. The mini hand transmitter is supplied with the following engraving: top 0 (= from) and bottom I (= one). According to the user manual, the radio module contained in the radio minihand transmitter can be learned in encrypted form into all encryptable actuators of the series 61 and 71 as well as into the FAM14. For this purpose, the radio-taster encryption rocker FTWW is required. Encryptable actuators carry the key pictogram. Colour: white Range: 30 m Signal transmission: radio Number of channels: 2 Installation type: other material: plastic Material quality: thermoplastic Window transmitter: No Suitable for display element: Yes Hand transmitter: Yes Wall transmitter: No Remote control: Yes Halogen-free: Yes Surface: untreated Surface finish: matt Suitable for switch: Yes Suitable for dimmer: Yes

Universal dimming switch without N connection, Power MOSFET up to 200W. Stand-by-Lower only 0.5 W, with control inputs for light sensor and light switch, minimum brightness, mode of operation and dimming speed adjustable, in the event that light switch cannot be replaced by light sensor, a separate control input for light switch is present, with children's room circuit, and slumber circuit nominal voltage: 230 W Color: blue Operation type: rotary knob Halogen-free: Yes Load type: universal. Stand-by loss only 0.5 Watt. With control inputs for light sensor and light switch. Minimum brightness, operating mode and dimming speed adjustable. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimming switch for R and C loads up to 200W, depending on the ventilation conditions. Dimmable ESL and 230V LED lamps in the operating mode phase section up to 200W or in the operating mode phase section up to 40W, depending on the ventilation conditions. In the case of dimmable 230V LED lamps, which also light slightly in the switched-off state, a basic load element GLE must be connected parallel to the lamp. L-loads (inductive loads, for example wound transformers) must not be connected. Switching in the zero passage with soft-on and soft-out for lamp protection. Control voltage, supply voltage and switching voltage 230W. Minimum load 4W. Short control commands turn on/off, permanent control changes brightness up to maximum value. An interruption of the control changes the dimming direction. Set

Energy consumption indicator for series installation The energy consumption indicator EVA12 measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories Eltako- AC counters of class B at MID (1%), the starting current is 20 mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Up to 24 hours, up to 31 days, up to 12 months and up to 24 years can be completed. The memory can be reset. Maximum current (value): 32 A Energy consumption display with display - smart metering for support rail. Stand-by loss only 0.5 Watt. The energy consumption indicator measures the active energy like an alternating current meter on the basis of the current flowing between the input and the output and stores the consumption in non-volatile memories. The accuracy corresponds to all Eltako- AC counters of class B at MID (1%), the starting current is 20mA. In this way, the energy consumption display precisely reproduces the measurement of the meter installed elsewhere in the building for electricity billing. The display is divided into 3 fields. Totalreset: In order to start storing the values in exact hours, a total set is recommended at a reasonable time after installation. To do this, hold the MODE and SELECT keys simultaneously for 5 seconds until RES appears in field 1. If SELECT is now briefly pressed, all memories are set to zero. After that, the program automatically returns to the normal display.

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours as well as the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1 Watt. Stand-by-loss only 0.02 - 0.6 Watt. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Times between 0.1 seconds and 40 hours are adjustable. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. Depending on the connection of the power supply to the terminals B1-A2 or B2-A2, two different functional levels can be selected. control voltage 1: 8 - 230 W control voltage type 1: AC/DC switching power fluorescent lamps parallel: 500 VA 1. Time range from/to: 40 - 0.1 Function: Multifunction Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductor: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA. Time unit: minutes/hour assembly type: DIN rail

Radio button with rocker and double rocker batteryless radio button, 868 Mhz, for up to 4 different radio signals, is delivered completely with rockers, double rocker, intermediate frame, snap plate and radio module, for cover frame Busch Reflex and Duro radio button for frame internal dimensions 55x55mm with radius, 15mm high. Creates the energy for radio telegrams even when pressing a button, therefore without connecting line and no stand-by loss. For Busch Reflex and Duro cover frame. Included are a rocker, a double rocker, a fastening frame, a holding plate (all the same color), the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then screw the holding plate - with the latches at the top and bottom -, snap the frame with the fastening frame and snap the set radio module with rocker - marking 0 on the back always at the top. For screw fastening

Radio button with rocker and double rocker batteryless radio button, 868 Mhz, for up to 4 different radio signals, is delivered completely with rockers, double rocker, intermediate frame, snap plate and radio module, for cover frame Busch Reflex and Duro radio button for frame internal dimensions 55x55mm with radius, 15mm high. Creates the energy for radio telegrams even when pressing a button, therefore without connecting line and no stand-by loss. For Busch Reflex and Duro cover frame. Included are a rocker, a double rocker, a fastening frame, a holding plate (all the same color), the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then screw the holding plate - with the latches at the top and bottom -, snap the frame with the fastening frame and snap the set radio module with rocker - marking 0 on the back always at the top. For screw fastening

multifunction time relays for mounting on support rail DIN-EN 50 022, digitally adjustable universal voltage multifunction time relays MFZ12DDX-8.230 V UC, 10A/250V AC, universal control voltage 8..230V UC, supply voltage such as the control voltage, with Eltako-Duplex technology TLE: 1 number of contacts as changer: 1 voltage type for actuation: AC Digital adjustable multifunction time relay with 18 functions. Stand-by loss only 0.05 - 0.5 Watt. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Both the function and the times are entered with keystroke and displayed digitally on an LC display. Only two buttons are to be used. In the time setting, all values can be entered within the preselected time frame (0.1-9.9 or 1-99 seconds, minutes or hours). The longest time is 99 hours. 600 time settings are possible. The entered time(s) is constantly displayed digitally. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network.