Dehn

Multi-pole surge arrester SPD VT2, type 2 according to EN 61643-11, consisting of base part and plugged protective modules. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B – 1 and higher.

Multi-pole surge arrester DEHNguard M YPV SCI, type 2 according to EN 50539-11 with three-stage DC switching device consisting of base part and plugged protective modules. Combined cutting and short-circuiting device with safe electrical separation in the protective module. To protect low-voltage consumer systems from overvoltages. For use according to IEC 60364-7-712:2002-05 (building photovoltaic supply systems).Overvoltage arrester DEHNguard M YPV SCI 1000Multi-pole, modular, pluggable photovoltaic conductor up to 1000 V DCwith 3-stage DC switch, width 3TEDefective indicatorType 2 according to EN 50539-11 Suitable for IEC 60364-712Safe electrical separation in the protection moduleMaximum PV voltage: Total leakage current: 40 kAProtection level: Short-circuit strength Iscpv: 10 kA

Single-pole surge arrester DEHNguard S, type 2 according to EN 61643-11, consisting of base part and plugged protective module. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B– 1 and higher.Overvoltage arrester DEHNguard S 2751-pole, modular, plug-in surge arresterwidth 1TE, Defective indicatorConductor type 2 according to EN 61643-11Maximum continuous voltage: 275 V ac/350 V dcProtection level: Rated output current: 20 kAShort-circuit strength: 50 kAeffEnergetic coordination according to DIN EN 62305-4 Head of the Red/Line family

Multi-pole surge arrester DEHNguard M, type 2 according to EN 61643-11, consisting of base part and plugged protective modules. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B– 1 and higher.

Lightning current-carrying DRL plug magazine 10 DA for almost all applications and expandable with DRL protection plug to the combination arrester, the integrated separating strip contacts allow testing, measuring and patching when plugged protection, the three-pole gas discharge arresters have a fail-safe function with optical display in case of defect

DEHNprotector® combined overvoltage protection for energy and data sides of a digital network connection NT, also suitable for telephone and fax machines, with optical operating and defect display connection input / output: RJ12 socket / RJ12 socket occupancy: 3/4 incl. Accessories suitable for RJ 11/12 and TAE connectors inserter according to the flash protection zone concept at interfaces 2-3 and higher

DEHNcord® Universal and flexible. Two- or one-pole surge arresters in compact design. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at interfaces 0B - 1 and higher. Function / defect display by green-red marking in the viewing window. Conductor type 2 according to EN 61643-11.Overvoltage arrester DEHNcord L 2P 275Two-pole surge arresters for all 230 V installation systemsConductor type 2 according to EN 61643-11for use in cable duct systems,Underfloor systems and equipment storage boxesDefective indicatorMaximum continuous voltage: 275 V acProtection level: Rated output current: 5 kATotal leakage current: 20 kAMax. net overcurrent protection: 25 A gGor B/C 16 AEnergetic coordination according to DIN EN 62 305-4 Conductors of the Red/Line family

BLITZDUCTOR® XT base part BXT BAS 4-pole, universal through-clamp for accommodating the arrester module without signal calculation, the reliable grounding of the arrester module is produced by means of a snap-fit fastening by means of the hat rail support base, since no components of the protection circuit are located in the base part, the maintenance work is limited to the protective modules connection cross-section in a continuous connection material 0.08 - 4 mm

TNC modular complete 3-pin circuit for TN-C systems with 230/400 V / 50 Hz - nominal voltage, multi-pole, modular overvoltage conductors in functional abduct design, for protection of low-voltage consumer systems against overvoltages, for use in lightning protection zone concept at interfaces 0B - 1 and higher, conductor type 2 according to EN 61643-11, ready-to-connectOvervoltage arrester DEHNguard M TNC 275 FM3-pole, modular, plug-in overvoltage arrester for 230/400 V TN-C systems, width 3TEwith telecommunication contactConductor type 2 according to EN 61643-11Defective indicatorMaximum continuous voltage: 275 V acProtection level: Rated output current: 20 kAShort-circuit strength: 50 kAeffEnergetic coordination according to DIN EN 62305-4 Head of the Red/Line family Factory: DEHN Type: DG M TNC 275 FM Art. No: 952305 or equivalent.

for upper and lower earth compounds, 60 x 60 mm, screws and nuts M8, with intermediate plate, DIN 48 845 D, for connections Rd/Rd, Rd/FI, FI/FI

DEHNshield® multi-pole combination arrester DEHNshield Basic, type 1 + type 2 according to EN 61643-11 based on spark gaps. Space-saving spark gap technology with only 1 TE / pole allows compact design. To protect residential buildings when retrofitting or refurbishment. Enables terminal protection. Meets all requirements of DIN VDE 0100-534 and DIN VDE 0100-443. Can be used directly at the feed point of the electrical system.Combi Devi Shield B TT 255 FM4-pin combination conductor for 230/400 V- TT- and TN (C) -S systems, Width 4 TE, with telecommunication contact Conductor type 1 + type 2 according to EN 61643-11Meets all requirements of DIN VDE 0100-534 and DIN VDE 0100-443spark gap technology with downstream current limitation Defective indicator Maximum continuous voltage: 255 V AC Protection level: Flash current (10/350): 30 kA Energetic coordination according to DIN EN 62305-4 Conductor of the Red/Line family, as well as directly to the terminal

for universal use as cross, T and parallel clamps, two-piece, thread in the bottom part with hexagonal screw M10 DIN 933

for upper and lower earth compounds, 60 x 60 mm, screws and nuts M8, with intermediate plate, DIN 48 845 D, for connections Rd/Rd, Rd/FI, FI/FI