Dispensers FR

Moisture chamber branch box with casting gel Practical branch box with membrane passage, for conductor cross-sections of 0.5-2.5 mm2, resistant to salt water and UV radiation, environmental compatible, high flexibility thanks to removable transparent casting resin, longevity under permanent moisture action, areas of application: open air and interiors with high moisture effect, with NYY suitable for earth cans. 0.5-2.5 mm2, assembly instructions, cleaning cloth, sanding paper, funnel for convenient vertical casting, protection class IP54. Windproof, halogen-free. Length: 85 mm Width: 85 mm Depth: 40 mm Inner depth: 38 mm Material: plastic Type of housing passage: sealing membrane

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 110x110x66 mm For cable Ø: 5.2-17 mm / M25 Max. Conductor cross section: 6.0 mm2

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 85x85x51 mm For cable Ø: 3-12 mm / M20 Max. Conductor cross section: 4.0 mm2

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 76x76x51 mm For cable Ø: 3-14 mm Max. Conductor cross-section: 2.5 mm2

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 140x140x82 mm For cable Ø: 6-21 mm / M20-M32 Max. Conductor cross-section: 10.0 mm2

Branch boxes, with clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV resistant type 308, 407 and 607 integrated thread (no counter nut required). Type 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids, seawater. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: Through 4 internal openings outside the sealing area or with type 308 and 407 with quick mounting bracket. 4 unreleasable lid screws. Screw clamps 5-pin. Type 308: Clamp 2.5 mm2, cable insert 8 side, membrane insert, 400 W Type 407: Clamp 4.0 mm2, cable insert 7 side +2 in the bottom, membrane insert, 690 W Type 607: Clamp 6 mm2, cable insert 7 side +3 in the bottom, membrane insert, 690 W Type 1010: Clamp 10mm2, cable insert 10 side +2 in the bottom, with gasket, 690 W14. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 110x110x66 mm For cable Ø: 5.2-17 mm / M25 Max. Conductor cross section: 6.0 mm2

Branch boxes, with clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV resistant type 308, 407 and 607 integrated thread (no counter nut required). Type 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids, seawater. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: Through 4 internal openings outside the sealing area or with type 308 and 407 with quick mounting bracket. 4 unreleasable lid screws. Screw clamps 5-pin. Type 308: Clamp 2.5 mm2, cable insert 8 side, membrane insert, 400 W Type 407: Clamp 4.0 mm2, cable insert 7 side +2 in the bottom, membrane insert, 690 W Type 607: Clamp 6 mm2, cable insert 7 side +3 in the bottom, membrane insert, 690 W Type 1010: Clamp 10mm2, cable insert 10 side +2 in the bottom, with gasket, 690 W14. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 85x85x51 mm For cable Ø: 3-12 mm / M20 Max. Conductor cross section: 4.0 mm2

Branch boxes, with clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV resistant type 308, 407 and 607 integrated thread (no counter nut required). Type 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids, seawater. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: Through 4 internal openings outside the sealing area or with type 308 and 407 with quick mounting bracket. 4 unreleasable lid screws. Screw clamps 5-pin. Type 308: Clamp 2.5 mm2, cable insert 8 side, membrane insert, 400 W Type 407: Clamp 4.0 mm2, cable insert 7 side +2 in the bottom, membrane insert, 690 W Type 607: Clamp 6 mm2, cable insert 7 side +3 in the bottom, membrane insert, 690 W Type 1010: Clamp 10mm2, cable insert 10 side +2 in the bottom, with gasket, 690 W14. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 140x140x82 mm For cable Ø: 6-21 mm / M20-M32 Max. Conductor cross section: 10 mm2

Branch boxes, with clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV resistant type 308, 407 and 607 integrated thread (no counter nut required). Type 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids, seawater. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: Through 4 internal openings outside the sealing area or with type 308 and 407 with quick mounting bracket. 4 unreleasable lid screws. Screw clamps 5-pin. Type 308: Clamp 2.5 mm2, cable insert 8 side, membrane insert, 400 W Type 407: Clamp 4.0 mm2, cable insert 7 side +2 in the bottom, membrane insert, 690 W Type 607: Clamp 6 mm2, cable insert 7 side +3 in the bottom, membrane insert, 690 W Type 1010: Clamp 10mm2, cable insert 10 side +2 in the bottom, with gasket, 690 W14. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 160x140x82 mm For cable Ø: 3-12 mm / M20-M25 Max. Conductor cross section: 10 mm2

Branch boxes, without clamps Material: polypropylene, fiberglass reinforced. Sealing: thermoplastic elastomer. Housing of two components (robusted housing and elastic insertion membranes). Flame retardant according to EN 60695-2-11. Halogen-free. Impact resistant and UV-resistant. Type 308, 407 and 607 integrated thread (no mating nut required). Type 108, 407, 607 and 1010. Chemical resistance: resistant to alkalis and inorganic acids. Voltage cracking: low. Temperature resistance: -30°C to +100°C, short to approx. Installation temperature: -5°C to +60°C. Incandescent wire test: 750°C. Colour: grey. Mounting options: 4 internal openings (except type 108 with 2 internal openings) outside the sealing area or type 108, 308 and 407 with quick mounting brackets. 4 unreleasable lid screws. Protection type according to EN 60529. Protection type: IP 66; IP 67 with screw connections. In the case of design protection IP 66 - sweat water formation possible. By using casting gel or pressure compensation cable screw connections which serve to reduce condensation water, a condensation water formation can be strongly limited and the protection class IP 66 is maintained. Condensation water openings are present at the rear, the protection is reduced when punched out. Minimum order quantity: 1 piece External dimensions: 160x140x82 mm For cable Ø: 3-12 mm / M20-M25 Max. Conductor cross-section: 10.0 mm2

Moisture chamber outlets for safety circuits Thermoplastic flame-retardant material, IP55 with condensation water opening, bottom inlets M20, external fastening points, opening cutters included, halogen-free, design: empty, without clamps, length: 85 mm, width: 85 mm depth: 37 mm, introductions: 12. Color: red

Moisture chamber outlets for safety circuits Thermoplastic flame-retardant material, IP55 with condensation water opening, bottom inlets M20, external fastening points, opening cutters included, halogen-free, design: empty, without clamps, length: 85 mm, width: 85 mm depth: 37 mm, introductions: 12. Color: green

Moisture area outlets, loosely sprinkled thermoplastic flame-retardant material, IP55 with condensation water opening, 4 floor inlets M20, empty without clamps, external fastening points, opening cutter beiligend, halogen-free, operating temperature range -25 °C to 40 °C Length: 85 mm Width: 85 mm Depth: 37 mm Protection type (IP): IP54 Color: grey lid: non-transparent Number of inserts 12

Thermoplastic flame-retardant material, IP55 with condensation water opening, bottom inserts M20, external fastening points, opening cutter, halogen-free, protection type: IP 54, application temperature range: -25 °C to 40 °C, color: grey. Depth: 37 mm. Length: 85 mm Width: 85 mm Depth: 37 mm Number of inserts: 12

Moisture area outlets, loosely sprinkled thermoplastic flame-retardant material, IP55 with condensation water opening, 4 bottom inlets M20, empty without clamps, external fastening points, opening cutter beiligend, halogen-free, use temperature range -25 °C to 40 °C Length: 75 mm Width: 75 mm Depth: 37 mm Protection type (IP): IP54 Colour: grey lid: non-transparent Number of inserts: 7