Eltako

Current surge switches for mounting on support rails DIN-EN 60715 TH35 rated switching power 16 A / 250 W AC or. 10 A / 400 W AC with manual actuation and switching position display mechanical storage of the switching position Electromechanical current surge switch with manual actuation and switching position display. Switch-on time 100%. Tax payable 5-6W. Contact distance 3mm. Distance control connections/contact > 6mm. Number of locks: 1 Number of openers: 1 Width in division units: 1 Rated switching current: 16 A Control voltage 1: 230 - W Control voltage type 1: AC Installation depth: 55 mm Installation type: DIN rail Frequency of control voltage 1: 50 - 50 Hz Voltage type of supply voltage: AC Supply voltage range: 250 - 250 W Max. Bulb load: 2300 W Max. Lamp load: 2300 VA Max. Fluorescent lamp load (Duo circuit): 2300 VA Max. Fluorescent lamp load (parallel compensated): 500 VA Max. Switching current (cos phi = 0.6): 10 A manual operation possible: Yes

Current relays for mounting on support rail DIN-EN 60715 TH35, potential-free 16 A /250 W AC, stand-by loss only 0.8 Watt current relay, stand-by loss only 0.8 Watt. Mounting unit for mounting on support rail (1 TE). To this end, simply connect the N conductor to the terminal (N) and L to 1 (L). This results in an additional stand-by consumption of only 0.1 Watt. If the contact is used for controlling switching devices which themselves do not switch in the zero passage, (N) should not be connected, since the additional closing delay otherwise causes the opposite. With an internal ring core current converter, the alternating current flowing via a consumer W1 is compared with the set value from 0.1A to a maximum of 32A and, when exceeded, a relay switches off a consumer W2 connected to 2 within 0.5 seconds or a consumer W3 connected to 3. Adjustment accuracy ±5%. From 25A, the relay always switches on. The most modern hybrid technology combines the advantages of wear-free electronic control with the high power of special relays. The current base A is set with the lower latching rotary switch A. TLE: 1 Number of contacts as changer: 1 Rated control voltage Us at AC 50 Hz: 230 - W

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours and the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sine wave, 0.1A. Time range from/to: 40 - 0.1 Function: Response delay Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductor: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA. Time unit: minutes/hour Mounting type: DIN rail Analog adjustable time relay. Stand-by-loss only 0.02 - 0.4 Watt. This analog-adjustable time relay is identical to the multifunction time relay, but has only one function. To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence.

Bus bridge connectors for wire connections of bus and power supply bridges, series 14, 45 cm long, 4-wire strand with soldered plug-in bridges on both sides Bus system EIB/KNX: No Bus system Funkbus: Yes Bus system Powernet: No Mounting type: other number of connections: 2 Bus system LON: No Other bus systems: without bus bridge connectors for wire connections of bus bridges. 4-wire cord with soldered plugs on both sides. The BBW14 Bus Bridge Connector can connect bus parts on various support rails. In order to connect series assembly units of the series 14 with transverse wiring bus and power supply with plug-in bridges on various support rails in a switch cabinet or distributor in a space-saving manner, bus bridge connectors are plugged onto at the end of a series of devices and at the beginning of the next series of devices.

Radio Set Dimmen Blister Pack Dimmen consists of a battery and lineless, radio button F4T65 in pure white, and a universal dimmor FUD61NPN-230V. The dimmer recognizes the type of lamp independently and allows the adjustment of the minimum brightness and the dimming speed Blister-Pack Dimmen consists of a battery- and line-free radio button F4T65 in pure white glossy and a universal dimmor FUD61NPN-230V. The dimmer recognizes the lamp type independently and allows the adjustment of the minimum brightness and the dimming speed. F4T65-wg: radio button for single mounting 84x84x16mm or mounting in the e-design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1E, a rocker, a double rocker, a fastening frame, a holding plate, the radio module and an adhesive film. Radio buttons with a rocker can send two, radio buttons with double rocker can send four evaluateable signals. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. The radio sensor illumination FTB can then also be latched from behind to the holding plate. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. Hi

Blister-Pack Dimmen consists of a battery and lineless FT55 radio button in pure white shiny and a universal dimmor FUD61NPN-230V. The dimmer recognizes the lamp type independently and allows the adjustment of the minimum brightness and the dimming speed. FT55-wg: radio button, 80x80mm outside, frame internal dimensions 55x55mm, 15mm high. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R, a rocker W55, a double rocker DW55 (all the same color), a fastening frame BRF, the holding plate HP, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. The radio sensor illumination FTB can then also be latched from behind to the holding plate. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When gluing first the set holding plate with frame and fastening frame ? glue with the latches on top and bottom. Then the set radio module with rocker ? Marking 0 on the back always snap up. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then screw the holding plate with the latches on top and bottom, the frame with the fastening frame

Blister-Pack Switching includes a battery-free and line-free, radio button F4T65 in pure white gloss, as well as a switch actuator FSR61-230V, with power surge switch function Blister-Pack Switching includes a battery-free and line-free radio button F4T65 in pure white glossy and a switch actuator FSR61-230V with power surge switch. F4T65-wg: radio button for single mounting 84x84x16mm or mounting in the e-design switch system. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R1E, a rocker, a double rocker, a fastening frame, a holding plate, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. The radio sensor illumination FTB can then also be latched from behind to the holding plate. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When glued, first attach the set holding plate with frame and fastening frame - with the latches on top and bottom. Then the set radio module with rocker - marking 0 on the back always up - snap in. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then the holding plate - with the

Blister-Pack Switching includes a battery- and line-free, radio button FT55 in pure white gloss, as well as a switch actuator FSR61-230V, with power surge switch function Blister-Pack Switching includes a battery- and line-free radio button FT55 in pure white gloss and a switch actuator FSR61-230V with power surge switch function. FT55-wg: radio button, 80x80mm outside, frame internal dimensions 55x55mm, 15mm high. Creates the energy for radio telegrams even at key pressure, therefore without connection line and no stand-by loss. Included are the frame R, a rocker W55, a double rocker DW55 (all the same color), a fastening frame BRF, the holding plate HP, the radio module and an adhesive film. Radio buttons with a rocker can send two evaluateable signals: press the rocker at the top and press the rocker at the bottom. Radio buttons with double rocker can send four evaluateable signals: press two rockers up and down. The holding plate can be screwed onto a flat surface or glued to the wall, to glass or to furniture by means of the attached adhesive film. The sleeves present in the can are used for screw fastening via a 55mm switch box. The radio sensor illumination FTB can then also be latched from behind to the holding plate. From work, the double rocker is locked onto the radio module. If these are to be exchanged for the large rocker, then pull the rocker halves forward and do not bend towards the center. Then the large rocker snaps on in such a way that its markings 0 and I correspond to the radio module on the rear side. When gluing first the set holding plate with frame and fastening frame ? glue with the latches on top and bottom. Then the set radio module with rocker ? Marking 0 on the back always snap up. Before screwing, release the frame with fastening frame from the holding plate. To this end, press the detents of the holding plate outwardly. Then the holding plate with the latch

If a plurality of installation relays are permanently excited, ensure sufficient ventilation according to the power loss calculation. The spacer increases a distance from the neighboring device of 9 mm. Distance piece for the production and maintenance of a ventilation distance in the case of very warm series installation devices, e.g. dimmers from 300W/400W and continuous electromechanical current surge switches. Width: 9 mm Depth: 55 mm Height: 80 mm

Electrical power meter Maximum power 3x80A, Stand-by-loss only 0.5 Watt per path, Row-mounting device for mounting on support rail DIN-EN 60715 TH35 in installation cabinets with protection class IP51, 4 division units = 70 mm wide, 58 mm deep, accuracy class B (1)%, with S0 interface, which measures directly measuring rotary power meter

Electricity meter Maximum current 3x80A, series mounting device for mounting on support rail DIN-EN 60715 TH35 in installation cabinets with protection class IP51, accuracy class 1 (1)%, with SO interface, 800 Imp/kWh, it can be connected 1, 2 or 3 external conductors with current consumption up to 80 A, the starting current is 2oma, the N connection must be present

Voltage meter, electronic for mounting on support rail DIN-EN 60715 TH35 with adjustable converter ratio, accuracy class B (1)%, S0 interface, measures the active energy on the basis of the currents flowing through the converter, it is possible to connect 1, 2 or 3 converters with secondary currents up to 5A, starting current is 10 ma, N connection must be present, the total power and resettable memory can be displayed

Mounting type: brushing Color: white Operation type: rotary/printing knob Halogen-free: Yes Composition: other load type: universal Serial dimmer: No Conveyor input: No Luminous accumulator: Yes Applicable with button: Yes Applicable with motion detector: No Applicable with presence detector: No Applicable with time switch/timer: No Applicable with radio button: No 80x80x25mm or installation in the FT55 switch system. Installation depth 33mm. Universal dimming switch with rotary knob, Power MOSFET up to 300W. Automatic lamp detection. Minimum brightness and maximum brightness adjustable. Stand-by loss only 0.14 Watt. Universal dimming switch for lamps up to 300W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Supply, switching and control voltage 230V. No minimum load required. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. Mounting: Mounting plate on. After adjusting the rotary switches, remove the red insulating cap and plug the rotary knob. The insulating cap should remain in the DTD55 for later use. Then snap the frame and plug the front panel. Attention! Before assembly and disassembly always turn off the mains voltage! With the left %-Drehschalter the minimum brightness (fully dimmed) can be set. With the middle %-Drehschalter the maximum

Rotary-Tast Dimming Switch for Single Mount 84x84x25mm or assembly into the E-Design switch system. Installation depth 33 mm. Universal dimming switch with rotary knob, Power MOSFET up to 300W. Automatic lamp detection. Minimum brightness and maximum brightness adjustable. Stand-by loss only 0.14 Watt. Universal dimming switch for lamps up to 300W, depending on the ventilation conditions. Dimmable energy-saving lamps ESL and dimmable 230V LED lamps additionally depend on lamp electronics. Switching in the zero passage with soft-on and soft-out for lamp protection. Supply, switching and control voltage 230V. No minimum load required. The set brightness level remains stored when switching off (memory). In the event of a power failure, the switching position and the brightness stage are stored and is switched on when the supply voltage is returned. Automatic electronic overload protection and overtemperature shutdown. Mounting: Mounting plate on. After adjusting the rotary switches, remove the red insulating cap and plug the rotary knob. The insulating cap should remain in the DTD65 for later use. Then snap the frame and plug the front panel. Attention! Before assembly and disassembly always turn off the mains voltage! With the left %-Drehschalter the minimum brightness (fully dimmed) can be set. With the middle %-Drehschalter the maximum brightness (fully dimmed) can be set. The right rotary switch adjusts the operating mode: AUTO allows the dimming of all lamp types. LC is a comfort position for LED lamps, which cannot be dimmed far enough on AUTO (phase section) due to construction and must therefore be forced to phase out. EC is a comfort position for energy-saving lamps, which must be switched on with an increased voltage due to the construction, so that they can also be switched on safely again cold. Operation: In the center of rotation

Multifunction time relays for mounting on support rail DIN-EN 60715 TH35, for all control voltages from 8 to 230W DC and AC (50/60 Hz), times between 0.1 seconds and 40 hours with the time bases 0.1, 0.5, 2 and 5 seconds, 1, 2 and 5 minutes, 1, 2 and 4 hours as well as the multiplier of 1-10 are adjustable, contact circuit in the zero crossing of the sinus wave, 0.1 Watt-by-adjustable time. Stand-by-loss only 0.02 - 0.4 Watt. This analog adjustable time relay is identical to the multifunction time relay, but has only one function. In the EAW12DX-UC type, a rotary switch can be used to set the functions of switch-on wipers (EW), switch-off wipers (AW) or switch-on and switch-off wipers (EAW). To this end, simply connect the N conductor to the terminal (N) and L to 15 (L). This results in an additional stand-by consumption of only 0.1 Watt. Universal control voltage 8..230V UC. Supply voltage like the control voltage. Time range from 0.1 seconds to 40 hours. By using a bistable relay, there is no coil loss power and no heating as a result even in the switched-on state. After installation, wait for the automatic short synchronization before the switched consumer is placed on the network. The light-emitting diode under the large rotary switch informs about the contact position during the time sequence. control voltage 1: 8 - 230 W control voltage type 1: AC/DC switching power fluorescent lamps parallel: 500 VA 1. Time range from/to: 40 - 0.1 Function: Switch-on/off switch relays Number of switches: 1 Switching power Incandescent lamps: 2000 W Width in division units: 1 Supply voltage range: 8 - 230 W Switching power Fluorescent lamps inductiv: 1000 VA Mounting height: 58 mm Switching power Fluorescent lamps DUO: 1000 VA Actuating type: analog with multifunction 1. Time unit: minutes/hour assembly type: DIN rail