List of products by brand Dehn

for universal use as cross, T and parallel clamps, two-piece, thread in the bottom part with hexagonal screw M10 DIN 933

for upper and lower earth compounds, 60 x 60 mm, screws and nuts M8, with intermediate plate, DIN 48 845 D, for connections Rd/Rd, Rd/FI, FI/FI

for Rd 7-10 Ø and Fl -40, DIN 48852

for upper and lower earth compounds, 60 x 60 mm, screws and nuts M8, with intermediate plate, DIN 48 845 D, for connections Rd/Rd, Rd/FI, FI/FI

Type K12 for main potential compensation, version with VDE characters according to DIN VDE 0100, part 410/540 and DIN EN 62305-3 comb-shaped contact rail, with 12 contact tongues, 10 clamps for Rd 2.5 to 95 mm2 or Rd Ø 10 mm, 1 clamp for Fl up to 4 x 30 mm

BLITZDUCTOR® XT base part BXT BAS 4-pole, universal through-clamp for accommodating the arrester module without signal calculation, the reliable grounding of the arrester module is produced by means of a snap-fit fastening by means of the hat rail support base, since no components of the protection circuit are located in the base part, the maintenance work is limited to the protective modules connection cross-section in a continuous connection material 0.08 - 4 mm

DEHNcord® Universal and flexible. Two- or one-pole surge arresters in compact design. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at interfaces 0B - 1 and higher. Function / defect display by green-red marking in the viewing window. Conductor type 2 according to EN 61643-11.Overvoltage arrester DEHNcord L 2P 275Two-pole surge arresters for all 230 V installation systemsConductor type 2 according to EN 61643-11for use in cable duct systems,Underfloor systems and equipment storage boxesDefective indicatorMaximum continuous voltage: 275 V acProtection level: Rated output current: 5 kATotal leakage current: 20 kAMax. net overcurrent protection: 25 A gGor B/C 16 AEnergetic coordination according to DIN EN 62 305-4 Conductors of the Red/Line family

Single-pole surge arrester DEHNguard S, type 2 according to EN 61643-11, consisting of base part and plugged protective module. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B– 1 and higher.Overvoltage arrester DEHNguard S 2751-pole, modular, plug-in surge arresterwidth 1TE, Defective indicatorConductor type 2 according to EN 61643-11Maximum continuous voltage: 275 V ac/350 V dcProtection level: Rated output current: 20 kAShort-circuit strength: 50 kAeffEnergetic coordination according to DIN EN 62305-4 Head of the Red/Line family

Overvoltage arresters DEHNrail M 2P 2552-pole, modular, plug-in overvoltage arrester to protect end devices of industrial electronicswidth 1TE, Defective indicatorConductor type 3 according to EN 61643-11Maximum continuous voltage: 255 V ac/dcTotal leakage current: 5 kAProtection level L/N: Prevention: 25 A gG or B 25 AEnergetic coordination according to DIN EN 62305-4 Head of the Red/Line family

Überspannungs-Ableiter DEHNguard M TNC 2753-poliger, modularer, steckbarer Überspannungs-Ableiter für TN-C-Systeme, Breite 3TE Ableiter Typ 2 nach EN 61643-11DefektanzeigeHöchste Dauerspannung: 275 V acSchutzpegel: <= 1,5 kVNennableitstoßstrom: 20 kAKurzschlußfestigkeit: 50 kAeffEnergetische Koordination nach DIN EN 62305-4 Ableiter der Red/Line-Familie Fabrikat: DEHN + SÖHNE Typ: DG M TNC 275 Art.-Nr.: 952300

Multi-pole surge arrester SPD VT2, type 2 according to EN 61643-11, consisting of base part and plugged protective modules. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B – 1 and higher.

Overvoltage arrester DEHNguard M TNS 2754-pole, modular, pluggable overvoltage arrester for 230/400 V TN-S systems, width 4TE Conductor type 2 according to EN 61643-11Defective indicatorMaximum continuous voltage: 275 V ac Protection level: Rated output current: 20 kAShort-circuit strength: 50 kAeffEnergetic coordination according to DIN EN 62305-4Head of the Red/Line family

DEHNprotector® combined overvoltage protection for energy and data sides of a digital network connection NT, also suitable for telephone and fax machines, with optical operating and defect display connection input / output: RJ12 socket / RJ12 socket occupancy: 3/4 incl. Accessories suitable for RJ 11/12 and TAE connectors inserter according to the flash protection zone concept at interfaces 2-3 and higher

Multi-pole surge arrester DEHNguard M, type 2 according to EN 61643-11, consisting of base part and plugged protective modules. High device safety due to thermal dynamic control. To protect low-voltage consumer systems from overvoltages. For use in the flash protection zone concept at the interfaces 0B– 1 and higher.

Overvoltage arrester DEHNguard M TNS 275 FM 4-pole modular, plug-in overvoltage arrester for 230/400 V TN-S systems, width 4TE with telecommunication contact arrester type 2 according to EN 61643-11 defect indicator Maximum continuous voltage: 275 V ac Protection level: