List of products by brand Eaton

Plug-in for PLS., CLS., PKN., PFIM, PFHM, (with auxiliary switch), any switchgear combinations with or without auxiliary switch possible, only a few components, 2 angle types per rail cross-section for three-phase displacement, common cover profile with end caps for ZV-SS etc. ZV-SS-80AShort-circuit and insulation resistance tested according to IEC/EN 60439-1Measurement current In A: 50Version: flatGalvanized: NoLength mm: 1000Width mm: 8Height mm: 2Flexible: no

1 piece Eaton ZV-N-05TE connection angle for busbar 50AMeasurement current In A: 80Galvanized: NoLength mm: 30Width mm: 7Height mm: 25Flexible: no

Eaton ZV-L2/L3 Connection angle for busbar 50A 1 pieceMeasurement current In A: 50Galvanized: NoLength mm: 35Width mm: 15Height mm: 12Flexible: no

1 piece Eaton ZV-L1/N connection angle for busbar 50AMeasurement current In A: 50Galvanized: NoLength mm: 25Width mm: 14Height mm: 10Flexible: no

Contact protection, power rail, contact protection, switchgear for industrial applications and high-end construction, BB-EV

Suitable for: Z-profileVersion: end capLength mm: 22Cover width mm: 6.5Material: plastic

Design according to IEC/EN 62019, screwless assembly, subsequently snap-on to PLS and PKNM, ZP-IHK, ZP-WHK: additionally 1x husk pack can be snapped onto itself, specified minimum voltages apply per switching path. Attention in series circuits!, through contact material and construction especially suitable forSmall voltages, contact function with relative movement (self-cleaning contacts), ZP-NHK: Function of one of the two changer contacts switchable from “auxiliary switches” to “start signal switches”, trigger signal contact reports electrical triggering, test button for contact function “electr. Redemption’Accessories for FI/LS combination switchAccessories for circuit breakersBasic function AccessoriesTrigger signal contactApplicationSwitching devices for industrial and commercial applicationsProduct rangeAccessoriesAccessibilitymountable from left to right: LS, FI/LSuniversalAdditional equipmentSignal switchesPlant-mountednoConstruction width (TE)0.5Number of locks0Number of openers0Number of changers2Number of fault signal switches0Measurement switching currentA4Measurement voltageV250Type of voltageACWith autotest for fault current functionnoSuitable for max. Number of poles of the main contact unit (total)2Suitable for max. Current intensity of the main contact unitA4

Design according to IEC/EN 62019, screwless assembly, subsequently snap-on to PLS and PKNM, ZP-IHK, ZP-WHK: additionally 1x husk pack can be snapped onto itself, specified minimum voltages apply per switching path. Attention in series circuits!, by contact material and construction particularly suitable for small voltages, contact function with relative movement (self-cleaning contacts), ZP-NHK: Function of one of the two changer contacts switchable from “auxiliary switches” to “trigger signal switches”, trigger signal contact reports electrical triggering, test button for contact function ”electr. Redemption’

Switching functionSwitchNumber of locks0Number of openers0Number of changers0Number1Rated currentA40Measurement voltageV400Min. Measurement voltageV230Measuring capacityKA0Short-circuit strength (Icw)KA3Type of voltageACForce separation (according to DIN VDE 0113)noWith signal lampnoColor of the calottenot applicableLampsnot applicableLampsnot applicableMax. lamp powerW0Width in division units1Installation depthmm60Type of protection (IP)IP40

Höhe


mm
370



Breite


mm
210



Verlängerungsstück



nein



Farbe



grau



RAL-Nummer



7035

Accessories for Sewing System

Switching device for the voluntary or tariff current limitation of consumer equipment, version according to EN/IEC 60898-1, EN/IEC 60947, EVU-approbated, easy to switch on from the current customer, setting screw under a sealable cap

Switching device for the voluntary or tariff current limitation of consumer equipment, version according to EN/IEC 60898-1, EN/IEC 60947, EVU-approbated, easy to switch on from the current customer, setting screw under a sealable cap

Block displacement for PLN. (1TE), delivery with end capsNumber of phases4Number3Suitable for number of devices13Partial dimensionmm1795Cross-sectionmm210Lengthmm232Number of division units3Duration of measurement IuA50Design of the electrical connectionPinInsulatedyesMeasurement surge voltageKV0Conditional measurement short-circuit current IqKA25Max. Rated operating voltage UeV415Measurement short-term current resistance IcwKA0Suitable for N-wire devicesyesSuitable for devices with auxiliary switchno

Safety load disconnector, rated operating voltage 230/400 VAC, 1-pin 110 VDC, 2-pin 220 VDC, suitable for melting inserts with operating class gG (gL) , aM, current encoding by safety set, plombable, feeding on both sides possible, screw capless plug-in technology, suitable for fuses D01: 1, 2, 4, 6, 10, 16A, D02: 2047